Media added by Doug J

Navigation

Browse albums

Media comments

  • ToddL214
    Finished!
    Those replacement bulkheads look great and appear to match well to the other woodwork I can see in the photos. I'll try to figure out how to...
  • Captain Grey Beard
    SERENITY
    You can use both panels at the same time. Because they are completely seperate sytems. The only reason you have a master over ride switch on you...
  • Captain Grey Beard
    SERENITY
    I am replacing the original panel all together. The original panel is not waterproof and is down by the floor. I'm also adding circuits. The...
  • Captain Grey Beard
    SERENITY
    Yes, you can have the DC panel & the AC panel active at the same time. They are electricity seperate systems.
  • hudson_rogue
    SERENITY
    And you don't have an override like on a house generator breaker, you just make sure all switches except your master/battery switch are off while...

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
I did away with the OEM plastic tubing. Replaced it with PVC

I did away with the OEM plastic tubing. Replaced it with PVC

  • 0
  • 0
This is what the laz floor looks like installed. I have since made a wood floor. But this is a descent, easy, inexpensive option.

This is what the laz floor looks like installed. I have since made a wood floor. But this is a descent, easy, inexpensive option.

  • 0
  • 0
The laz floor made in two pieces, for easy insertion and removal.

The laz floor made in two pieces, for easy insertion and removal.

  • 0
  • 0
Laz floor. I wanted a floor to keep stuff out of any water in there. But I also wanted to be able to remove it if needed. This worked fairly well. I made it out of sched 40 pvc, real easy to do.

Laz floor. I wanted a floor to keep stuff out of any water in there. But I also wanted to be able to remove it if needed. This worked fairly well. I made it out of sched 40 pvc, real easy to do.

  • 0
  • 0
Laz floor just sits loose, not fastened, I like to be able to remove it if needed.

Laz floor just sits loose, not fastened, I like to be able to remove it if needed.

  • 0
  • 0
Laz floor, I made this from scrap wood. I'll re-do it with better wood and seal it.

Laz floor, I made this from scrap wood. I'll re-do it with better wood and seal it.

  • 0
  • 0
The boards just lift out, leaving frame below. Access to the bilge pump or transducer is easy my removing only the middle board.

The boards just lift out, leaving frame below. Access to the bilge pump or transducer is easy my removing only the middle board.

  • 0
  • 0
Hatch for storage below vee berth

Hatch for storage below vee berth

  • 0
  • 0
New mast cap, put the old flat one at the base of the mast. I drilled holes in the mast crane added some sheaves in there, and moved the main halyard to it, and added a topping lift in addition to the back stay.

New mast cap, put the old flat one at the base of the mast. I drilled holes in the mast crane added some sheaves in there, and moved the main halyard to it, and added a topping lift in addition to the back stay.

  • 0
  • 0
Harken traveler

Harken traveler

  • 0
  • 0
Mast raising system on deck stowage, starboard side.

Mast raising system on deck stowage, starboard side.

  • 0
  • 0
Rudder lifting blocks

Rudder lifting blocks

  • 0
  • 0
Top Bottom