Media
Navigation
Media comments
-
Finished!Those replacement bulkheads look great and appear to match well to the other woodwork I can see in the photos. I'll try to figure out how to... -
SERENITYYou can use both panels at the same time. Because they are completely seperate sytems. The only reason you have a master over ride switch on you... -
SERENITYI am replacing the original panel all together. The original panel is not waterproof and is down by the floor. I'm also adding circuits. The...
-
SERENITYYes, you can have the DC panel & the AC panel active at the same time. They are electricity seperate systems.
-
SERENITYAnd you don't have an override like on a house generator breaker, you just make sure all switches except your master/battery switch are off while...
Media statistics
- Albums
- 3,799
- Uploaded media
- 22,708
- Embedded media
- 19
- Comments
- 425
- Disk usage
- 2.2 GB
scan This was mast raising the old way. Regardless of which way you decide to raise/lower your mast there are certain rules that you need to go by or you chance losing your mast over the side with a broken tabernacle. 1. Always have the wind coming directly from aft i f you are raising the mast from aft and visa versa if raising from the bow. 2. The boat and/or the boat sitting on the trailer needs o be level from side to side. 3. Take your time and be on the lookout for snags or twist in the stays. 4. Watch out for overhead obstructions like tree branches and wires. 5. If your stays have T bar fittings that fit into slots in the mast, make sure that they are seated correctly. You can buy rubber mast plugs that fit into the slots with hold the T bar in place. 6. If you have a good roller furler like the CDI or Harken, I suggest that you install pivot bridles and baby stays. Otherwise have someone hold the furler in line with the mast as it goes up or comes down.
- Joe11688
- Aug 3, 2013
- 0
- 0
![GetAttachment[1]](/data/xfmg/thumbnail/19/19261-f92fca4de1ef62c8d5d812a958062b00.jpg?1565728645)
DSC00781 This first Gin Pole that I built was made of Oak. I made so that it could be taken apart for easy stowage. If you decide to build one of these it would be wise to have your mast raised so that you can decide where you want to place it on the mast. I place the crutch of the Gin Pole on my mast and tie it off just about even with the Goose Neck. This height will allow me to take up on my block and tackle and I'm using my boom vang with about 55' of braid line attached to it. This gives me enough line to stretch the blocks out. Figure on making the Gin pole long enough to be within an inch or two from the forestay when it's in place on the mast. The Gin Pole just provides the angle needed to raise/lower the mast and that's all. Some guys mount a small boat winch on the Gin Pole and use it to raise/lower the mast. Myself, I prefer the block & tackle or my Boom Vang.
- Joe11688
- Aug 3, 2013
- 0
- 0
DSC00450 As I had mentioned previously, you need some sort of a mast crutch to hold the mast up off the cabin while you pin the tabernacle. A small roller in the mast crutch will allow you to roll the mast forward or aft. I was fortunate to get a full stern rail on my new O'Day 222 only because I requested it. They only install about 20 of these on these boats that year so I'm told. I had a welder make me up that mast crutch to my existing rail. He only charged me about $230 back then I think. I built that wooden crutch and later added the roller. My friend Wayne Barlow gave me the idea of having a roller in the crutch. I had been lifting my mast and walking it back to the crutch and putting it in place-- like a dumbbell. Heck it's easier to roll it back and forth.
- Joe11688
- Aug 3, 2013
- 0
- 0
DSC08342 This mast only weighs about 65 lbs and it's easy to raise without the Gin Pole. I used to raise the mast by hand and use a 3/8"X 60' nylon line with a sheave connected to the bow stem chainplate to hold the mast up. I spliced an eye on one end of the line and connected it to my Jib shackle. The Jib halyard was raised and cleated to the mast with the line running through the sheave on the bow. Once the mast was up, I'd take the line around the mast above the goose neck fitting, and tie it off to my starboard bow cleat after pulling all the slack out of the line. Then the fore stay could be connected. If you have a quick release lever on your backstay or a Johnson Handy-Lock, you can throw enough slack into your forestay so that you can remove it. You never need to touch the other turnbuckles on the O'Day 222. A press button quick pin can be used on the fore stay. Do not use a fast pin!
- Joe11688
- Aug 3, 2013
- 0
- 0
