Media

Navigation

Browse albums

Media comments

  • ToddL214
    Finished!
    Those replacement bulkheads look great and appear to match well to the other woodwork I can see in the photos. I'll try to figure out how to...
  • Captain Grey Beard
    SERENITY
    You can use both panels at the same time. Because they are completely seperate sytems. The only reason you have a master over ride switch on you...
  • Captain Grey Beard
    SERENITY
    I am replacing the original panel all together. The original panel is not waterproof and is down by the floor. I'm also adding circuits. The...
  • Captain Grey Beard
    SERENITY
    Yes, you can have the DC panel & the AC panel active at the same time. They are electricity seperate systems.
  • hudson_rogue
    SERENITY
    And you don't have an override like on a house generator breaker, you just make sure all switches except your master/battery switch are off while...

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
trailer couple needs replaced too.

trailer couple needs replaced too.

  • 0
  • 0
rusty winch has to go !

rusty winch has to go !

  • 0
  • 0
disassemble everything !!

disassemble everything !!

  • 0
  • 0
Starting on the trailer. Hubs, bearings, springs, tires, rims.

Starting on the trailer. Hubs, bearings, springs, tires, rims.

  • 0
  • 0
Hull and bottom completed.

Hull and bottom completed.

  • 0
  • 0
finished the wet sanding and buffed it out with a super cut marine buffing compound for gel coats. then applied a coat of New Finish, Once a year car polish. It was an awesome result compared to what it looked like before.

finished the wet sanding and buffed it out with a super cut marine buffing compound for gel coats. then applied a coat of New Finish, Once a year car polish. It was an awesome result compared to what it looked like before.

  • 0
  • 0
bottom and keel painted 3 coats.

bottom and keel painted 3 coats.

  • 0
  • 0
I spent many days wet sanding the gel coat w/ 600 grit wet sand paper and a sanding block. a couple of drops of dish soap in a spray bottle of warm water works a lubricant to ease the process somewhat.

I spent many days wet sanding the gel coat w/ 600 grit wet sand paper and a sanding block. a couple of drops of dish soap in a spray bottle of warm water works a lubricant to ease the process somewhat.

  • 0
  • 0
Cleaned the hull with soft scrub w/ bleach and a kitchen scrubby to remove all the oxidation. worked great !!

Cleaned the hull with soft scrub w/ bleach and a kitchen scrubby to remove all the oxidation. worked great !!

  • 0
  • 0
Grinding the keel to remove rust.

Grinding the keel to remove rust.

  • 0
  • 0
Almost ready.

Almost ready.

  • 0
  • 0
Looking good.

Looking good.

  • 0
  • 0
A lot of work here.

A lot of work here.

  • 0
  • 0
Starting on sanding the bottom.

Starting on sanding the bottom.

  • 0
  • 0
bottom is solid but is a mess. Well, here goes !!

bottom is solid but is a mess. Well, here goes !!

  • 0
  • 0
rusty ole winch.

rusty ole winch.

  • 0
  • 0
the hull is the original gel coat, but it's a mess.

the hull is the original gel coat, but it's a mess.

  • 0
  • 0
works great.

works great.

  • 0
  • 0
hair dryer on high to remove the stripes.

hair dryer on high to remove the stripes.

  • 0
  • 0
yuck.

yuck.

  • 0
  • 0
Oh my, Looks like a family of squirrels were living here.

Oh my, Looks like a family of squirrels were living here.

  • 0
  • 0
Hang on, I got this !!

Hang on, I got this !!

  • 0
  • 0
where's my pressure washer ?

where's my pressure washer ?

  • 0
  • 0
dirty and neglected, this is sad.

dirty and neglected, this is sad.

  • 0
  • 0
Top Bottom