Media

Navigation

Browse albums

Media comments

  • ToddL214
    Finished!
    Those replacement bulkheads look great and appear to match well to the other woodwork I can see in the photos. I'll try to figure out how to...
  • Captain Grey Beard
    SERENITY
    You can use both panels at the same time. Because they are completely seperate sytems. The only reason you have a master over ride switch on you...
  • Captain Grey Beard
    SERENITY
    I am replacing the original panel all together. The original panel is not waterproof and is down by the floor. I'm also adding circuits. The...
  • Captain Grey Beard
    SERENITY
    Yes, you can have the DC panel & the AC panel active at the same time. They are electricity seperate systems.
  • hudson_rogue
    SERENITY
    And you don't have an override like on a house generator breaker, you just make sure all switches except your master/battery switch are off while...

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
Headed out the first time.

Headed out the first time.

  • 0
  • 0
The partition separates the drink side from the food side is so we can grab cool drinks through the top hatch without losing all the cold air from the food side

The partition separates the drink side from the food side is so we can grab cool drinks through the top hatch without losing all the cold air from the food side

  • 0
  • 0
I made a partition in the cooler using a 1/2" thick cutting board and rubber weather stripping from the hardware store. And we freeze 3 gallon jugs of water to line the bottom of the cooler. These kept beers and food cold throughout a 4 day trip on their first use. And the best thing is - no pool of water at the bottom!

I made a partition in the cooler using a 1/2" thick cutting board and rubber weather stripping from the hardware store. And we freeze 3 gallon jugs of water to line the bottom of the cooler. These kept beers and food cold throughout a 4 day trip on their first use. And the best thing is - no pool of water at the bottom!

  • 0
  • 0
Water Supply to Pump (newl)

Water Supply to Pump (newl)

  • 0
  • 0
Water Supply at Water Heater (original)

Water Supply at Water Heater (original)

  • 0
  • 0
Water Supply at Water Heater (new)

Water Supply at Water Heater (new)

  • 0
  • 0
Water Supply at Pump (original)

Water Supply at Pump (original)

  • 0
  • 0
Water Supply at Pump (new)

Water Supply at Pump (new)

  • 0
  • 0
Water Supply at Pump (new 1)

Water Supply at Pump (new 1)

  • 0
  • 0
Water Supply at Outside Shower (original)

Water Supply at Outside Shower (original)

  • 0
  • 0
Water Supply at Outside Shower (new 1)

Water Supply at Outside Shower (new 1)

  • 0
  • 0
Water Supply at Head (original)

Water Supply at Head (original)

  • 0
  • 0
Water Supply at Head (new)

Water Supply at Head (new)

  • 0
  • 0

  • 0
  • 0

  • 0
  • 0
Sony Marine, a great improvement over the old Duel speakers

Sony Marine, a great improvement over the old Duel speakers

  • 0
  • 0
you can see the close-up here how I drilled the bolt holes for the chocks oversized, then epoxied, then drilled them the correct size for the hardware. this is much stronger way to mount load-bearing hardware and there's no place for water to seep into the fiberglass. I then used bed-it tape around the holes, and a little around the head of each bolt

you can see the close-up here how I drilled the bolt holes for the chocks oversized, then epoxied, then drilled them the correct size for the hardware. this is much stronger way to mount load-bearing hardware and there's no place for water to seep into the fiberglass. I then used bed-it tape around the holes, and a little around the head of each bolt

  • 0
  • 0
anchor light and antenna are all finished

anchor light and antenna are all finished

  • 0
  • 0
new anchor light on the mast cap

new anchor light on the mast cap

  • 0
  • 0
the topsides of the through-deck fittings

the topsides of the through-deck fittings

  • 0
  • 0
The system uses a SS double ended stud to secure the mast. Once the must is up, the gin pole winch keeps it in place freeing both hands to secure the fore stay.

The system uses a SS double ended stud to secure the mast. Once the must is up, the gin pole winch keeps it in place freeing both hands to secure the fore stay.

  • 0
  • 0
Tape keeps the cable out of the way and the turnbuckle properly aligned.

Tape keeps the cable out of the way and the turnbuckle properly aligned.

  • 0
  • 0
The two external SS plates can be safely removed after stepping the mast. I have not see this solution elsewhere but it works well. A first attempt with aluminum plates instead of of the SS was marginally successful as the larger size made the removal the gin pole after the operation somewhat difficult.

The two external SS plates can be safely removed after stepping the mast. I have not see this solution elsewhere but it works well. A first attempt with aluminum plates instead of of the SS was marginally successful as the larger size made the removal the gin pole after the operation somewhat difficult.

  • 0
  • 0
Notice the block at the top of the gin pole

Notice the block at the top of the gin pole

  • 0
  • 0
Top Bottom