Media

Navigation

Browse albums

Media comments

  • ToddL214
    Finished!
    Those replacement bulkheads look great and appear to match well to the other woodwork I can see in the photos. I'll try to figure out how to...
  • Captain Grey Beard
    SERENITY
    You can use both panels at the same time. Because they are completely seperate sytems. The only reason you have a master over ride switch on you...
  • Captain Grey Beard
    SERENITY
    I am replacing the original panel all together. The original panel is not waterproof and is down by the floor. I'm also adding circuits. The...
  • Captain Grey Beard
    SERENITY
    Yes, you can have the DC panel & the AC panel active at the same time. They are electricity seperate systems.
  • hudson_rogue
    SERENITY
    And you don't have an override like on a house generator breaker, you just make sure all switches except your master/battery switch are off while...

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
Genaker flying off the wind

Genaker flying off the wind

  • 0
  • 0
Star Fish Island Kingston Reef

Star Fish Island Kingston Reef

  • 0
  • 0
Redesigned rudder and pintel box

Redesigned rudder and pintel box

  • 0
  • 0
Replacement fin and beaver tail bulb

Replacement fin and beaver tail bulb

  • 0
  • 0
The benefits of a vertically lifting keel

The benefits of a vertically lifting keel

  • 0
  • 0
Moon Over Exuma Sound

Moon Over Exuma Sound

  • 0
  • 0
Port tack

Port tack

  • 0
  • 0
AmelEden at rest

AmelEden at rest

  • 0
  • 0
Sail Collage

Sail Collage

  • 0
  • 0
IMG 2115

IMG 2115

  • 0
  • 0
Mt Rainier in the background

Mt Rainier in the background

  • 0
  • 0
Gusty today - solo sail

Gusty today - solo sail

  • 0
  • 0
Persistence

Persistence

  • 0
  • 0
Bought her in Booth Bay, Maine

Bought her in Booth Bay, Maine

  • 0
  • 0
She now moors at Falmouth Town Landing, Falmouth, Maine

She now moors at Falmouth Town Landing, Falmouth, Maine

  • 0
  • 0
100 1174

100 1174

  • 0
  • 0
Just in

Just in

  • 0
  • 0
Backing on the ramp at Eglin AFB

Backing on the ramp at Eglin AFB

  • 0
  • 0
Test fit of new block looks great. I will clean it up and add some sealant. Then to fix my mistake and place the access port in the correct position. I might just fill it back up with foam and seal it in as I should not need to mess with this again for many years.

Test fit of new block looks great. I will clean it up and add some sealant. Then to fix my mistake and place the access port in the correct position. I might just fill it back up with foam and seal it in as I should not need to mess with this again for many years.

  • 0
  • 0
Out with the old. By the way if installing an access port it is much higher than I estimated on the Oday 19 put the port as high as you can. I estimated it way too low. Great thing with fiberglass is you can hide your mistakes.

Out with the old. By the way if installing an access port it is much higher than I estimated on the Oday 19 put the port as high as you can. I estimated it way too low. Great thing with fiberglass is you can hide your mistakes.

  • 0
  • 0
You can not even tell where the seam is. This is great stuff I will be using in many future projects.

You can not even tell where the seam is. This is great stuff I will be using in many future projects.

  • 0
  • 0
New Bow Eye block cut from PVC board two 3.5" x 3/4" x 4" glued together. At least this will not rot out.

New Bow Eye block cut from PVC board two 3.5" x 3/4" x 4" glued together. At least this will not rot out.

  • 0
  • 0
The factory used steel nuts not stainless. No wonder the bow eye was loose.

The factory used steel nuts not stainless. No wonder the bow eye was loose.

  • 0
  • 0
At Dock

At Dock

  • 0
  • 0
Top Bottom