Media

Navigation

Browse albums

Media comments

  • A
    1975 o'day 22
    will be changing to led lights both mast and cabin along with nav lights. adding solar, adding bbq, rebedding all deck hardware and below water...
  • Monsterfish
    Looking forward to V-berth.
    Wow.....dream home!
  • D
    MacGregor 26s
    Das sind Teakleisten, die aufgeklebt, dann mit Schwarzer Masse ausgegossen und geschliffen wurden. Sieht immer noch aus wie neu.....
  • P
    Marilee-Interior.jpg
    This interior is gorgeous! What type of boat is this in?
  • JohnScott
    DSCN8846
    CHILD LABOR

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
Royal Jamaica Yacht Club

Royal Jamaica Yacht Club

  • 0
  • 0
Genaker flying off the wind

Genaker flying off the wind

  • 0
  • 0
Star Fish Island Kingston Reef

Star Fish Island Kingston Reef

  • 0
  • 0
Redesigned rudder and pintel box

Redesigned rudder and pintel box

  • 0
  • 0
Replacement fin and beaver tail bulb

Replacement fin and beaver tail bulb

  • 0
  • 0
The benefits of a vertically lifting keel

The benefits of a vertically lifting keel

  • 0
  • 0
Moon Over Exuma Sound

Moon Over Exuma Sound

  • 0
  • 0
Port tack

Port tack

  • 0
  • 0
AmelEden at rest

AmelEden at rest

  • 0
  • 0
Sail Collage

Sail Collage

  • 0
  • 0
IMG 2115

IMG 2115

  • 0
  • 0
Mt Rainier in the background

Mt Rainier in the background

  • 0
  • 0
Gusty today - solo sail

Gusty today - solo sail

  • 0
  • 0
Persistence

Persistence

  • 0
  • 0
Bought her in Booth Bay, Maine

Bought her in Booth Bay, Maine

  • 0
  • 0
She now moors at Falmouth Town Landing, Falmouth, Maine

She now moors at Falmouth Town Landing, Falmouth, Maine

  • 0
  • 0
100 1174

100 1174

  • 0
  • 0
Just in

Just in

  • 0
  • 0
Backing on the ramp at Eglin AFB

Backing on the ramp at Eglin AFB

  • 0
  • 0
Test fit of new block looks great. I will clean it up and add some sealant. Then to fix my mistake and place the access port in the correct position. I might just fill it back up with foam and seal it in as I should not need to mess with this again for many years.

Test fit of new block looks great. I will clean it up and add some sealant. Then to fix my mistake and place the access port in the correct position. I might just fill it back up with foam and seal it in as I should not need to mess with this again for many years.

  • 0
  • 0
Out with the old. By the way if installing an access port it is much higher than I estimated on the Oday 19 put the port as high as you can. I estimated it way too low. Great thing with fiberglass is you can hide your mistakes.

Out with the old. By the way if installing an access port it is much higher than I estimated on the Oday 19 put the port as high as you can. I estimated it way too low. Great thing with fiberglass is you can hide your mistakes.

  • 0
  • 0
You can not even tell where the seam is. This is great stuff I will be using in many future projects.

You can not even tell where the seam is. This is great stuff I will be using in many future projects.

  • 0
  • 0
New Bow Eye block cut from PVC board two 3.5" x 3/4" x 4" glued together. At least this will not rot out.

New Bow Eye block cut from PVC board two 3.5" x 3/4" x 4" glued together. At least this will not rot out.

  • 0
  • 0
The factory used steel nuts not stainless. No wonder the bow eye was loose.

The factory used steel nuts not stainless. No wonder the bow eye was loose.

  • 0
  • 0
Top Bottom