Media

Navigation

Browse albums

Media comments

  • North Texas Sailor
    10003920_10152058444073992_320766486_n
    This is a beautiful galley
  • L
    SAM 0324
    Neat boat, this looks like one of the original Willard built Lancer 30s. You can tell from the swept back keel that is similar to the C&C Mk I...
  • A
    1975 o'day 22
    will be changing to led lights both mast and cabin along with nav lights. adding solar, adding bbq, rebedding all deck hardware and below water...
  • Monsterfish
    Looking forward to V-berth.
    Wow.....dream home!
  • D
    MacGregor 26s
    Das sind Teakleisten, die aufgeklebt, dann mit Schwarzer Masse ausgegossen und geschliffen wurden. Sieht immer noch aus wie neu.....

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
Gusty today - solo sail

Gusty today - solo sail

  • 0
  • 0
Persistence

Persistence

  • 0
  • 0
Bought her in Booth Bay, Maine

Bought her in Booth Bay, Maine

  • 0
  • 0
She now moors at Falmouth Town Landing, Falmouth, Maine

She now moors at Falmouth Town Landing, Falmouth, Maine

  • 0
  • 0
100 1174

100 1174

  • 0
  • 0
Just in

Just in

  • 0
  • 0
Backing on the ramp at Eglin AFB

Backing on the ramp at Eglin AFB

  • 0
  • 0
Test fit of new block looks great. I will clean it up and add some sealant. Then to fix my mistake and place the access port in the correct position. I might just fill it back up with foam and seal it in as I should not need to mess with this again for many years.

Test fit of new block looks great. I will clean it up and add some sealant. Then to fix my mistake and place the access port in the correct position. I might just fill it back up with foam and seal it in as I should not need to mess with this again for many years.

  • 0
  • 0
Out with the old. By the way if installing an access port it is much higher than I estimated on the Oday 19 put the port as high as you can. I estimated it way too low. Great thing with fiberglass is you can hide your mistakes.

Out with the old. By the way if installing an access port it is much higher than I estimated on the Oday 19 put the port as high as you can. I estimated it way too low. Great thing with fiberglass is you can hide your mistakes.

  • 0
  • 0
You can not even tell where the seam is. This is great stuff I will be using in many future projects.

You can not even tell where the seam is. This is great stuff I will be using in many future projects.

  • 0
  • 0
New Bow Eye block cut from PVC board two 3.5" x 3/4" x 4" glued together. At least this will not rot out.

New Bow Eye block cut from PVC board two 3.5" x 3/4" x 4" glued together. At least this will not rot out.

  • 0
  • 0
The factory used steel nuts not stainless. No wonder the bow eye was loose.

The factory used steel nuts not stainless. No wonder the bow eye was loose.

  • 0
  • 0
At Dock

At Dock

  • 0
  • 0
Deck

Deck

  • 0
  • 0
Cabin

Cabin

  • 0
  • 0
Cabin

Cabin

  • 0
  • 0
Hunter 35

Hunter 35

  • 0
  • 0
MarquesasKeysFloridaSailto8

MarquesasKeysFloridaSailto8

  • 0
  • 0
Marquesas Keys Florida7

Marquesas Keys Florida7

  • 0
  • 0
Marquesas Keys Florida6

Marquesas Keys Florida6

  • 0
  • 0
Marquesas Keys Florida5

Marquesas Keys Florida5

  • 0
  • 0
Marquesas Keys Florida4

Marquesas Keys Florida4

  • 0
  • 0
Marquesas Keys Florida3

Marquesas Keys Florida3

  • 0
  • 0
Marquesas Keys Florida2

Marquesas Keys Florida2

  • 0
  • 0
Top Bottom