Media

Navigation

Browse albums

Media comments

  • North Texas Sailor
    10003920_10152058444073992_320766486_n
    This is a beautiful galley
  • L
    SAM 0324
    Neat boat, this looks like one of the original Willard built Lancer 30s. You can tell from the swept back keel that is similar to the C&C Mk I...
  • A
    1975 o'day 22
    will be changing to led lights both mast and cabin along with nav lights. adding solar, adding bbq, rebedding all deck hardware and below water...
  • Monsterfish
    Looking forward to V-berth.
    Wow.....dream home!
  • D
    MacGregor 26s
    Das sind Teakleisten, die aufgeklebt, dann mit Schwarzer Masse ausgegossen und geschliffen wurden. Sieht immer noch aus wie neu.....

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
Stereo installed and I don't like the "floating" look of it.

Stereo installed and I don't like the "floating" look of it.

  • 0
  • 0
Speakers installed in the beckson access ports (that way one could easily remove them later, and still have access to the motor mount and boarding ladder).

Speakers installed in the beckson access ports (that way one could easily remove them later, and still have access to the motor mount and boarding ladder).

  • 0
  • 0
Drill cut and run electrical for the stereo (that will be installed in the bulkhead).

Drill cut and run electrical for the stereo (that will be installed in the bulkhead).

  • 0
  • 0
Painting bottom paint on the rudder.

Painting bottom paint on the rudder.

  • 0
  • 0
Ladder pieced back together. This was an EBay find ladder for $50 shipped... came off an Oday 25... I added a larger rubber stopper to it, to reduce stress on the transom... But the fit is great, and it should provide at least 1 rung if not 2 below water level.

Ladder pieced back together. This was an EBay find ladder for $50 shipped... came off an Oday 25... I added a larger rubber stopper to it, to reduce stress on the transom... But the fit is great, and it should provide at least 1 rung if not 2 below water level.

  • 0
  • 0
Ladder installed, with backer, and 4200 sealing the holes.

Ladder installed, with backer, and 4200 sealing the holes.

  • 0
  • 0
The cockpit seat is getting glassed in, this is 2 layers of chopped strand.

The cockpit seat is getting glassed in, this is 2 layers of chopped strand.

  • 0
  • 0
This is me with my boarding ladder disassembled, fitting a plywood backer to it, and pre-drilling the holes. I later epoxied (actually poly resined) the board before installation.

This is me with my boarding ladder disassembled, fitting a plywood backer to it, and pre-drilling the holes. I later epoxied (actually poly resined) the board before installation.

  • 0
  • 0
Electronics installed no, I love how this turned out.

Electronics installed no, I love how this turned out.

  • 0
  • 0
Hatchboard keepers installed, black 1/4" starboard.

Hatchboard keepers installed, black 1/4" starboard.

  • 0
  • 0
Rouging out some starboard to fit electronics (covering a square hole and a round one).

Rouging out some starboard to fit electronics (covering a square hole and a round one).

  • 0
  • 0
Testing the ladder install, and location... this is held in ONLY by 2 temporary screws in this picture, I still need a backer plate and large bolts to secure it.

Testing the ladder install, and location... this is held in ONLY by 2 temporary screws in this picture, I still need a backer plate and large bolts to secure it.

  • 0
  • 0
Painting the daggerboard, yep its still about 2-3" in the hole but enough room to reach down and paint ALL but the bottom, I'll paint the bottom when the daggerboard is down again, also while I recoat the bottom... This is VC17m.

Painting the daggerboard, yep its still about 2-3" in the hole but enough room to reach down and paint ALL but the bottom, I'll paint the bottom when the daggerboard is down again, also while I recoat the bottom... This is VC17m.

  • 0
  • 0
Finding a way to haul out the daggerboard all 600lbs of it... to paint it.

Finding a way to haul out the daggerboard all 600lbs of it... to paint it.

  • 0
  • 0
New hatch slides installed.

New hatch slides installed.

  • 0
  • 0
Access ports going in (to access the motor mount and new stern boarding ladder).

Access ports going in (to access the motor mount and new stern boarding ladder).

  • 0
  • 0
New instrumentation going in.

New instrumentation going in.

  • 0
  • 0
Starting the port seat recoring project.

Starting the port seat recoring project.

  • 0
  • 0
Another shot of the core.

Another shot of the core.

  • 0
  • 0
note this is the port seat after traveler removal, note the core. That the FRP top layer with gelcoat intact sitting in front.

note this is the port seat after traveler removal, note the core. That the FRP top layer with gelcoat intact sitting in front.

  • 0
  • 0
Cockpit port seat before any work... also note the hatch and crib boards...

Cockpit port seat before any work... also note the hatch and crib boards...

  • 0
  • 0
image

image

  • 0
  • 0
Captain Jones

Captain Jones

  • 0
  • 0
DAY 1

DAY 1

  • 0
  • 0
Top Bottom