Media

Navigation

Browse albums

Media comments

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
Critical work done here.. porta pottie in, and new boards to keep it from sliding around. I'm going to redo this with a board up front for it, and stain them all, but this is a great way to start before the head would slide back and forth while heeling.

Critical work done here.. porta pottie in, and new boards to keep it from sliding around. I'm going to redo this with a board up front for it, and stain them all, but this is a great way to start before the head would slide back and forth while heeling.

  • 0
  • 0
Mast onboard again.

Mast onboard again.

  • 0
  • 0
Traveler going back in.

Traveler going back in.

  • 0
  • 0
Oh yeah, used standard double braid samson xls for the pole topping lift.

Oh yeah, used standard double braid samson xls for the pole topping lift.

  • 0
  • 0
Halyards are in!

Halyards are in!

  • 0
  • 0
Poof there is nonskid.. I used interlux non-skid additive to the gelcoat.. I sprinkled it on, then painted over the wet gelcoat... it was tough to get it to pattern well, but it worked well enough for me.

Poof there is nonskid.. I used interlux non-skid additive to the gelcoat.. I sprinkled it on, then painted over the wet gelcoat... it was tough to get it to pattern well, but it worked well enough for me.

  • 0
  • 0
Ah yes the gelcoat is cured, and sanded now. NOW it needs NONSKID!

Ah yes the gelcoat is cured, and sanded now. NOW it needs NONSKID!

  • 0
  • 0
This was actually my first eye splice, my main halyard, it has an easy wichard shackle you can remove from the eye...

This was actually my first eye splice, my main halyard, it has an easy wichard shackle you can remove from the eye...

  • 0
  • 0
Learning some new skills, this is 5/16" VPC double strand... learned how to eye splice using NERs demo video... these ronstan snap shackles are for the spin halyard and genoa halyard, they need to be spliced on... learning to do this saved me not only the cost of paying someone else to splice these, but also the cost of a shackle! Since I had good ones already!

Learning some new skills, this is 5/16" VPC double strand... learned how to eye splice using NERs demo video... these ronstan snap shackles are for the spin halyard and genoa halyard, they need to be spliced on... learning to do this saved me not only the cost of paying someone else to splice these, but also the cost of a shackle! Since I had good ones already!

  • 0
  • 0
Ugh, hate this part... outboard... boy am I glad I took it apart though... this is the old water pump impeller. one broken vane, and 3 more cracked.

Ugh, hate this part... outboard... boy am I glad I took it apart though... this is the old water pump impeller. one broken vane, and 3 more cracked.

  • 0
  • 0
AH yes legalities...

AH yes legalities...

  • 0
  • 0
This is the new name, yep we'll have a ritual for launch... cause this boat has had an extensive refit, it seemed appropriate to rechristen her... nope I didn't spell anything wrong... Was thinking of getting company logos for Goslings, Pussers, Mount Gay, Krakken, Pyrat, and lining them up below that name.

This is the new name, yep we'll have a ritual for launch... cause this boat has had an extensive refit, it seemed appropriate to rechristen her... nope I didn't spell anything wrong... Was thinking of getting company logos for Goslings, Pussers, Mount Gay, Krakken, Pyrat, and lining them up below that name.

  • 0
  • 0
This is starboard side with compound/polish/wax done.

This is starboard side with compound/polish/wax done.

  • 0
  • 0
Pulled the boat out to wash down the sanding dust. This is port side with no work done...

Pulled the boat out to wash down the sanding dust. This is port side with no work done...

  • 0
  • 0
cables run down into the V-berth

cables run down into the V-berth

  • 0
  • 0
Routing the wind transducer wire... I used micro C through deck connectors, and spliced the simnet cables.. we'll see if it worked. The wiring inside a simnet cable is identical to NMEA 2000, the connectors are just different.. I just needed a solution to allow me to disconnect the transducer for trailering.

Routing the wind transducer wire... I used micro C through deck connectors, and spliced the simnet cables.. we'll see if it worked. The wiring inside a simnet cable is identical to NMEA 2000, the connectors are just different.. I just needed a solution to allow me to disconnect the transducer for trailering.

  • 0
  • 0
Better shot of the masthead, I installed an LED anchor light too.

Better shot of the masthead, I installed an LED anchor light too.

  • 0
  • 0
Masthead after wiring was done.

Masthead after wiring was done.

  • 0
  • 0
Huge repair job done years ago, and gelcoat was all mismatched, and down to gray undercoat in places. My attempt was to gelcoat over it this was the masking portion, after sanding.

Huge repair job done years ago, and gelcoat was all mismatched, and down to gray undercoat in places. My attempt was to gelcoat over it this was the masking portion, after sanding.

  • 0
  • 0
Port cockpit seat getting gelcoated.

Port cockpit seat getting gelcoated.

  • 0
  • 0
my project, a shelf for under the stereo, to prevent people from smacking the radio while sitting on that berth.

my project, a shelf for under the stereo, to prevent people from smacking the radio while sitting on that berth.

  • 0
  • 0
mast painted (that was quick).

mast painted (that was quick).

  • 0
  • 0
mast getting a coat of black paint... note mast was white before.

mast getting a coat of black paint... note mast was white before.

  • 0
  • 0
Spreaders welded... note, the spreaders are "sealed" on the S2, if you leave the mast on the boat horizontal for the winter, rainwater drains down from the mast side into the spreaders, then freeze/thaw cycles bust the seams of the spreaders... best to drill a weep hole near the end (done later in this project after painting)>

Spreaders welded... note, the spreaders are "sealed" on the S2, if you leave the mast on the boat horizontal for the winter, rainwater drains down from the mast side into the spreaders, then freeze/thaw cycles bust the seams of the spreaders... best to drill a weep hole near the end (done later in this project after painting)>

  • 0
  • 0
Top Bottom