Media

Navigation

Browse albums

Media comments

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
Port seatee

Port seatee

  • 0
  • 0
Interior looking forward

Interior looking forward

  • 0
  • 0
Recently installed bimini

Recently installed bimini

  • 0
  • 0
Fall raft up sunset

Fall raft up sunset

  • 0
  • 0
New Shackles & Toggle Pins: The roller furling worked more smoothly when I changed the OEM shackles. Also replaced the clevis pin and split ring with a spring toggle pin at the bottom of the drum to allow quicker attachment when bending on the forestay.

New Shackles & Toggle Pins: The roller furling worked more smoothly when I changed the OEM shackles. Also replaced the clevis pin and split ring with a spring toggle pin at the bottom of the drum to allow quicker attachment when bending on the forestay.

  • 0
  • 0
Wide shot of outhaul hardware

Wide shot of outhaul hardware

  • 0
  • 0
Close Up of my outhaul (version 3) - I think I have it right now. I didn't want to install an internal clew outhaul as illustrated in the H15 manual because I had 'foamed' the boom along with the mast to help prevent turning turtle if/when I lay her down in a gust. There isn't much room between the clew and the end of the boom saddle and therefore to get some mechanical advantage I had to mount a second block, a cheek block, on the side of the boom and lead the line through a fairlead jamcleat.

Close Up of my outhaul (version 3) - I think I have it right now. I didn't want to install an internal clew outhaul as illustrated in the H15 manual because I had 'foamed' the boom along with the mast to help prevent turning turtle if/when I lay her down in a gust. There isn't much room between the clew and the end of the boom saddle and therefore to get some mechanical advantage I had to mount a second block, a cheek block, on the side of the boom and lead the line through a fairlead jamcleat.

  • 0
  • 0
CU Boat Vent II. Allows moisture to escape from under the cover to inhibit mildew.

CU Boat Vent II. Allows moisture to escape from under the cover to inhibit mildew.

  • 0
  • 0
Boat Cover with vents. This is a generic cover made for 4.5 meter aluminium dinghys.

Boat Cover with vents. This is a generic cover made for 4.5 meter aluminium dinghys.

  • 0
  • 0
Moved up the factory waterline as the boat sat a bit bow down and below the original waterline with the fresh water holding tank full

Moved up the factory waterline as the boat sat a bit bow down and below the original waterline with the fresh water holding tank full

  • 0
  • 0
Finished.... finally June 2010

Finished.... finally June 2010

  • 0
  • 0
After bottom painting with Petit Trinidad SR June 2010

After bottom painting with Petit Trinidad SR June 2010

  • 0
  • 0
Keel after refinish with Interlux 2000E June 2010

Keel after refinish with Interlux 2000E June 2010

  • 0
  • 0
yamaha37 photo

yamaha37 photo

  • 0
  • 0
starboard satee

starboard satee

  • 0
  • 0
port satee

port satee

  • 0
  • 0
IMG 0261

IMG 0261

  • 0
  • 0
IMG 0262

IMG 0262

  • 0
  • 0
IMG 0260

IMG 0260

  • 0
  • 0
galley 4

galley 4

  • 0
  • 0
galley 3

galley 3

  • 0
  • 0
galley 1

galley 1

  • 0
  • 0
dinette 1

dinette 1

  • 0
  • 0
2 Camas

2 Camas

  • 0
  • 0
Top Bottom