Ah, sometimes called the bag of terror. But, it doesn't have to be. If it is an asymmetrical, it is really handled much like a very large genoa most of the time. Since it is flown on the same side of the mainsail, you have to steer more into the wind than dead down wind because the mainsail is blanketing the sail. That is why many one design racing boats have retractable sprits (introduced by J/Boats). The sprit pushes the sail away from the main for clearer air. Now you can find after-market retractable sprits that can be retrofitted onto your deck for this purpose. For boats with the traditional spinnaker pole attached to the front of the mast, one can steer the boat more dead down wind than boats with an asymmetrical. But, you cannot steer the boat as far to windward with the spinnaker pole-mounted boat as you can with an asymmetrical, which again, is more like a very large genoa at that angle. Rule #1 is never put up the mainsail without the main being up first - especially in heavy air. I suppose you could do it in light air, but NEVER when it is blowing stink. When it fills, it very well might rip the line out of your hand. The mainsail will blanket the sail while raising it safely and in a more controlled situation than with no main. There is a limit as to when you will decide to not fly the spinnaker. Most cruisers will play it safe and fly it only when they feel comfortable doing so and that has a lot to do with the wind velocity and how many crew members you have to handle the sail. A boat with a spinnaker and pole requires more crew as the wind increases. Asymmetrical kites don't require the crew because for one thing......there is no pole to handle. Racers who sail their boats effectively, will have the sail ready to launch as they reach the windward mark and as they round the mark, the sail will be hoisted so that when they are on the new course (which usually requires a gybe), the sail will be full and flying keeping the boat at full speed. Of course it doesn't always go according as planned depending on the experience of the crew, if they are ready when they sail up to the mark and of course, there sometimes are other boats approaching the mark at the same time which may interfere with your rounding depending on right of way rules, or screw ups. There is a thing called a "gybe-set" too, where because of a given situation you raise the spinnaker, gybe the boat (and main) and THEN attach the pole on the new windward side. Cruisers aren't so concerned about being efficient when raising and they shouldn't be for competitive reasons. But, they want it to go smoothly and of course no one wants to look like they don't know what they are doing, but you can fast put those days aside when you actually figure it all out. I have written more about trimming the two basic types of spinnakers and won't do that now. Back in the old IOR days of racing there used to be another downwind sail used called the blooper, which is flown in tandem with the spinnaker poled to the mast. They were smaller and were designed to keep the boat balanced when you were sailing more downwind so that you could even out the pressure in the combined effort of the two sails. Back in the day, when I was young and agile and would do anything, I used to sit in the bow pulpit of a boat I used to race and have both the spinnaker and blooper flying as I trimmed it from the bow of the boat. The helm was secured and I was single-handling. Of course, if the wind got too strong, things could go wrong and so I did it mostly with moderate to lighter air. Something else that was used back in those days you don't see so much anymore is a reaching strut too. When you were driving the boat as close to the wind as you could possible physically sail the boat with a spinnaker, the spinnaker pole outboard end would be touching (or nearly so) the forestay after easing it all the way, and the sheet would be trimmed in as tightly as allowed to keep the boat tracking to windward. At that point you have to wonder if the genoa wouldn't be the better sail in that situation, but maybe it was because you got a good temporary wind shift or something, or you were trying to stay high on a competitor. The after guy (which is the other line on the opposite side of the boat than the sheet - attached to the pole), which leads aft has a very acute angle and sometimes it was difficult - especially on a larger boat - to trim the after guy because the angle was so tight. The reaching strut was attached to the side of the mast and was longer than half the beam so that the after guy could be threaded through the outboard end increasing the angle of the guy for better trimming. Now that you are all probably totally confused, I will stop. By all means fly your spinnaker. There's nothing neater than sailing down wind with a beautiful colored spinnaker under control and you will go faster too. It puts a grin on your face. I have sailed my cruising boat under spinnaker and there often isn't another cruising boat doing the same thing. I have a few kites and the last time I used one (with pole and there were only two of us), I was running down the West Channel of the Apostles towards Bayfield on a marvelous sunny summer day. I was the only boat with a kite up. When I got back to the marina several people approached me and asked if that was me with the kite up all the way down that channel. Of course racers (of which I am also one) will use their kites all the time. Oh, one more story. There have been a few times when aground in the Bahamas where I had to put a spinnaker up to heel the boat over enough to sail into deeper water too. So, all that cloth is helpful then too.