I use my spare main halyard. I take about 20 feet of line and tie one end to the outboard motor lifting handle and the other end to the halyard. This gives me enough halyard line in the cockpit to lead it off the stern. I let the admiral work the winch and the only weight I have is the horizontal weight while I guide the motor from one mount to the other, those being on the stern rail and the dink. Garhauer makes a nice motor lift that my friend has on his 44DS. My version is free. Good luck.Loading a Honda 2hp motor or similar from the aft end of our Hunter 41DS to a Zodiac dinghy is difficult for an older person like me (77 yrs old). Are there any clever ways to lower a motor down that would make it easy?
With a hard dinghy I absolutely agree, but rowing an inflatable in either current or wind could be a losing battle:cry:...Embrace the horror of using oars.
pros
light weight
stow easily
no gas storage needed
no starting problems
does not make the boat go as as fast but has unlimited range
maintains a active lifestyle (important for us old farts)
can be use as an anti boarding device in a pinch
can be use to "pole" around the boat to find which side is shllow when aground
no maintenance needed
they are quiet while in use
it is salty
cons
it requires effort
does not allow you to waterski
you don't get there as fast
you can't see where you are going easily
it takes some practice to learn
Bring the dink along side the starboard- or portside stern; secure it bow and stern after aligning the dinghy transom directly below where the motor is mounted on your stern rail. Have a lifting bridle on the engine (so it hangs vertically) with a tagline to the rail. Open the engine mount screws all the way then lower the engine right on to the transom. (Use a block to the deck somewhere if you need it; you're on the boat, not in the dinghy!) With practice you can drop it into position; the tagline keeps it from falling off and sinking. Of course, you now have to get into the dink to tighten the mounting screws. I go straight over the rail then down into the dink using a suspension step hung from the stanchion. To recover, reverse the process. Need only to vertically dead-lift the engine the distance from the dink transom to the rail mount using the tagline; perhaps 5 to 6 ft.Loading a Honda 2hp motor or similar from the aft end of our Hunter 41DS to a Zodiac dinghy is difficult for an older person like me (77 yrs old). Are there any clever ways to lower a motor down that would make it easy?
I agree with Centerline. Here is our setup. Boom works great with the arch on Hunters.use the boom... attach a block & tackle to the end of the boom, hoist the topping lift to raise the boom to create some headroom, then hoist the outboard with the tackle and swing it out over the dinghy....
the real problem with using any method other than you hands, arms and back, is that the dinghy is bouncing one direction, the mothership is rolling the other direction, and you are trying to keep from falling in the water while making the transfer. unless you are on a mill pond...
I don’t think your lecture is helpful to the OP of what should be. Different people have different abilities, and the OP was asking for tips that would make it easier.Your engine with oil and a full tank of gas will be a tad short of 30 lbs. Lifting and carrying the engine by its handle and walking a few steps should be within the capabilities of the average 77 year old. Your boat has an open transom providing the capability of setting the engine down on the swim platform next to the dinghy. Once more lift the engine and set it inside the dinghy. Get yourself inside the dinghy and slide the outboard leg over the transom. With the mount screws open pick it up once more and set it in place tightening the mounting screws. Handling the weight in a series of short intervals should not be too taxing. I have used outboard lifts and find that the physical exertion in setting them up and lifting and lowering the engine are more complicated and probably more demanding than just picking the small one up. Lifts are better suited for more heavier engines in boats that may lack an open transom. I have seen that an exercise regime of lifting weights can increase and maintain a persons ability to handle loads not only for weight but for balance. I think this is the easiest way.