Media

Navigation

Browse albums

Media comments

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
IMG 0124

IMG 0124

  • 0
  • 0
IMG 0125

IMG 0125

  • 0
  • 0
IMG 0123

IMG 0123

  • 0
  • 0
Boat cover 001 This is Cordura nylon. I purchased a 12x24 tarp and cut it to shape, and used over a kilometer of thread designed for Sunbrella sewn with a really cheap Brother sewing machine using #18 needles.

Boat cover 001 This is Cordura nylon. I purchased a 12x24 tarp and cut it to shape, and used over a kilometer of thread designed for Sunbrella sewn with a really cheap Brother sewing machine using #18 needles.

  • 0
  • 0
Interior5 Interior pieces prior to paint. Notice long strips along the V-berth section. Instead of placing the new section over the 2" section left behind, I scabbed these pieces underneath cut the new section to fall into place.

Interior5 Interior pieces prior to paint. Notice long strips along the V-berth section. Instead of placing the new section over the 2" section left behind, I scabbed these pieces underneath cut the new section to fall into place.

  • 0
  • 0
Cabin1209 V-berth "patterns". I cut the oval holes in these areas to acces space that would otherwise be inaccessible. I did this a few years ago in place, and in the replacement wood before installation.

Cabin1209 V-berth "patterns". I cut the oval holes in these areas to acces space that would otherwise be inaccessible. I did this a few years ago in place, and in the replacement wood before installation.

  • 0
  • 0
Cabin3 Companionway view of stripped cabin.

Cabin3 Companionway view of stripped cabin.

  • 0
  • 0
Cabin1202 V-berth area. Notice the hole drilled on the forward vertical surface of the sole pan. This was glassed over, as was the aft hole. Water was retained, and at best would seep to where I could removed it, but caused the rot in the bulkheads adjacent.

Cabin1202 V-berth area. Notice the hole drilled on the forward vertical surface of the sole pan. This was glassed over, as was the aft hole. Water was retained, and at best would seep to where I could removed it, but caused the rot in the bulkheads adjacent.

  • 0
  • 0
Cabin1050 Bunks removed. Bunk supports were also removed and replaced. The bunks are glassed to the hull, so I cut them with a jig saw about 2" in, cut the new bunks from the pattern and added the 2", then installed them over the old edge and screwed them in.

Cabin1050 Bunks removed. Bunk supports were also removed and replaced. The bunks are glassed to the hull, so I cut them with a jig saw about 2" in, cut the new bunks from the pattern and added the 2", then installed them over the old edge and screwed them in.

  • 0
  • 0
DSCN3843 Adhesive is 3M 5200.

DSCN3843 Adhesive is 3M 5200.

  • 0
  • 0
DSCN3839 Deck bedded to hull and pressed into place.

DSCN3839 Deck bedded to hull and pressed into place.

  • 0
  • 0
DSCN3530 Old bulkhead was used as template for shaping 12mm PVC foam.

DSCN3530 Old bulkhead was used as template for shaping 12mm PVC foam.

  • 0
  • 0
DSCN2957 Aft bulkhead removed.

DSCN2957 Aft bulkhead removed.

  • 0
  • 0
Aft bulkhead cut and kicked out of place. Cockpit support tube has been removed to accomodate a 20 gallon water tank that now acts as the support.

Aft bulkhead cut and kicked out of place. Cockpit support tube has been removed to accomodate a 20 gallon water tank that now acts as the support.

  • 0
  • 0
DSCN3790 While up I filled all the holes drilled along the gunwale after grinding out the area around them to a uniform depth. Filled with a little filler putty, but mostly glass cloth and resin. Putty offers little structural strength.

DSCN3790 While up I filled all the holes drilled along the gunwale after grinding out the area around them to a uniform depth. Filled with a little filler putty, but mostly glass cloth and resin. Putty offers little structural strength.

  • 0
  • 0
DSCN3527 This is the replacement PVC foam material with resin poured over it (I just had extra resin so figured it wouldn't hurt).

DSCN3527 This is the replacement PVC foam material with resin poured over it (I just had extra resin so figured it wouldn't hurt).

  • 0
  • 0
DSCN3415 These are the 4" pieces of ply used for core filler when manufactured.

DSCN3415 These are the 4" pieces of ply used for core filler when manufactured.

  • 0
  • 0
DSCN3525 Deck lifted. The bow proved the most challenging. The pin in the anchor locker goes through the hull and deck, and is glassed over.

DSCN3525 Deck lifted. The bow proved the most challenging. The pin in the anchor locker goes through the hull and deck, and is glassed over.

  • 0
  • 0
DSCN3370 This is the port rear stanchion area I was having water intrusion.

DSCN3370 This is the port rear stanchion area I was having water intrusion.

  • 0
  • 0
Lone Sailor on Moon River running between Savannah and Skidaway Island, GA.

Lone Sailor on Moon River running between Savannah and Skidaway Island, GA.

  • 0
  • 0
Freebrid Poster

Freebrid Poster

  • 0
  • 0
as seen through dodger

as seen through dodger

  • 0
  • 0
instrument pod cover

instrument pod cover

  • 0
  • 0
Cover for instrument pod

Cover for instrument pod

  • 0
  • 0
Top Bottom