Media

Navigation

Browse albums

Media comments

  • A
    1975 o'day 22
    will be changing to led lights both mast and cabin along with nav lights. adding solar, adding bbq, rebedding all deck hardware and below water...
  • Monsterfish
    Looking forward to V-berth.
    Wow.....dream home!
  • D
    MacGregor 26s
    Das sind Teakleisten, die aufgeklebt, dann mit Schwarzer Masse ausgegossen und geschliffen wurden. Sieht immer noch aus wie neu.....
  • P
    Marilee-Interior.jpg
    This interior is gorgeous! What type of boat is this in?
  • JohnScott
    DSCN8846
    CHILD LABOR

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
IMG 1162

IMG 1162

  • 0
  • 0
IMG 0660

IMG 0660

  • 0
  • 0
IMG 0665

IMG 0665

  • 0
  • 0
IMG 0671

IMG 0671

  • 0
  • 0
IMG 0666

IMG 0666

  • 0
  • 0
DSC01039 I'm able to raise my mast all by myself with this rig. Note the CDI Roller Furler. I have it roped off to my Gin pole with a rolling hitch tied to the furler luff.

DSC01039 I'm able to raise my mast all by myself with this rig. Note the CDI Roller Furler. I have it roped off to my Gin pole with a rolling hitch tied to the furler luff.

  • 0
  • 0
DSC01153 I finally found a good use for that triangular plate that came off my backstay as you can see in the pic. I had no need for it after I installed a traveler in front of my companionway.

DSC01153 I finally found a good use for that triangular plate that came off my backstay as you can see in the pic. I had no need for it after I installed a traveler in front of my companionway.

  • 0
  • 0
DSC01152 I used 1" stainless steel pipe with a 1-1/8"x 6" stainless steel collar welded to the one inch pipe. Fast pin is used to hold the pipes in place.

DSC01152 I used 1" stainless steel pipe with a 1-1/8"x 6" stainless steel collar welded to the one inch pipe. Fast pin is used to hold the pipes in place.

  • 0
  • 0
DSC01151 I used the same wood crutch from the other Gin Pole. I drilled a 1" hole into the wood so that the pipe fit into the crutch beyond the flange which is screwed in place.

DSC01151 I used the same wood crutch from the other Gin Pole. I drilled a 1" hole into the wood so that the pipe fit into the crutch beyond the flange which is screwed in place.

  • 0
  • 0
DSC01150 Here's my new Stainless Steel Gin Pole. I had my oldest son Steve weld it up for me. This rig works great and it all fits in a quarter birth compartment ready when needed.

DSC01150 Here's my new Stainless Steel Gin Pole. I had my oldest son Steve weld it up for me. This rig works great and it all fits in a quarter birth compartment ready when needed.

  • 0
  • 0
scan This was mast raising the old way. Regardless of which way you decide to raise/lower your mast there are certain rules that you need to go by or you chance losing your mast over the side with a broken tabernacle. 1. Always have the wind coming directly from aft i f you are raising the mast from aft and visa versa if raising from the bow. 2. The boat and/or the boat sitting on the trailer needs o be level from side to side. 3. Take your time and be on the lookout for snags or twist in the stays. 4. Watch out for overhead obstructions like tree branches and wires. 5. If your stays have T bar fittings that fit into slots in the mast, make sure that they are seated correctly. You can buy rubber mast plugs that fit into the slots with hold the T bar in place. 6. If you have a good roller furler like the CDI or Harken, I suggest that you install pivot bridles and baby stays. Otherwise have someone hold the furler in line with the mast as it goes up or comes down.

scan This was mast raising the old way. Regardless of which way you decide to raise/lower your mast there are certain rules that you need to go by or you chance losing your mast over the side with a broken tabernacle. 1. Always have the wind coming directly from aft i f you are raising the mast from aft and visa versa if raising from the bow. 2. The boat and/or the boat sitting on the trailer needs o be level from side to side. 3. Take your time and be on the lookout for snags or twist in the stays. 4. Watch out for overhead obstructions like tree branches and wires. 5. If your stays have T bar fittings that fit into slots in the mast, make sure that they are seated correctly. You can buy rubber mast plugs that fit into the slots with hold the T bar in place. 6. If you have a good roller furler like the CDI or Harken, I suggest that you install pivot bridles and baby stays. Otherwise have someone hold the furler in line with the mast as it goes up or comes down.

  • 0
  • 0
DSC00451 This is a detachable mast crutch that I use for trailering.

DSC00451 This is a detachable mast crutch that I use for trailering.

  • 0
  • 0
DSC00447 This is a Johnson Handy-Lock.

DSC00447 This is a Johnson Handy-Lock.

  • 0
  • 0
DSC00783 This is my old wooden Gin Pole. I'm using a stainless steel Gin Pole now.

DSC00783 This is my old wooden Gin Pole. I'm using a stainless steel Gin Pole now.

  • 0
  • 0
DSC00780 It's important to secure the pole to the mast so that it doesn't pull off when the mast is up.

DSC00780 It's important to secure the pole to the mast so that it doesn't pull off when the mast is up.

  • 0
  • 0
DCP 4532

DCP 4532

  • 0
  • 0
GetAttachment[1]

GetAttachment[1]

  • 0
  • 0
DSC00781 This first Gin Pole that I built was made of Oak. I made so that it could be taken apart for easy stowage. If you decide to build one of these it would be wise to have your mast raised so that you can decide where you want to place it on the mast. I place the crutch of the Gin Pole on my mast and tie it off just about even with the Goose Neck. This height will allow me to take up on my block and tackle and I'm using my boom vang with about 55' of braid line attached to it. This gives me enough line to stretch the blocks out. Figure on making the Gin pole long enough to be within an inch or two from the forestay when it's in place on the mast. The Gin Pole just provides the angle needed to raise/lower the mast and that's all. Some guys mount a small boat winch on the Gin Pole and use it to raise/lower the mast. Myself, I prefer the block & tackle or my Boom Vang.

DSC00781 This first Gin Pole that I built was made of Oak. I made so that it could be taken apart for easy stowage. If you decide to build one of these it would be wise to have your mast raised so that you can decide where you want to place it on the mast. I place the crutch of the Gin Pole on my mast and tie it off just about even with the Goose Neck. This height will allow me to take up on my block and tackle and I'm using my boom vang with about 55' of braid line attached to it. This gives me enough line to stretch the blocks out. Figure on making the Gin pole long enough to be within an inch or two from the forestay when it's in place on the mast. The Gin Pole just provides the angle needed to raise/lower the mast and that's all. Some guys mount a small boat winch on the Gin Pole and use it to raise/lower the mast. Myself, I prefer the block & tackle or my Boom Vang.

  • 0
  • 0
DSC00450 As I had mentioned previously, you need some sort of a mast crutch to hold the mast up off the cabin while you pin the tabernacle. A small roller in the mast crutch will allow you to roll the mast forward or aft. I was fortunate to get a full stern rail on my new O'Day 222 only because I requested it. They only install about 20 of these on these boats that year so I'm told. I had a welder make me up that mast crutch to my existing rail. He only charged me about $230 back then I think. I built that wooden crutch and later added the roller. My friend Wayne Barlow gave me the idea of having a roller in the crutch. I had been lifting my mast and walking it back to the crutch and putting it in place-- like a dumbbell. Heck it's easier to roll it back and forth.

DSC00450 As I had mentioned previously, you need some sort of a mast crutch to hold the mast up off the cabin while you pin the tabernacle. A small roller in the mast crutch will allow you to roll the mast forward or aft. I was fortunate to get a full stern rail on my new O'Day 222 only because I requested it. They only install about 20 of these on these boats that year so I'm told. I had a welder make me up that mast crutch to my existing rail. He only charged me about $230 back then I think. I built that wooden crutch and later added the roller. My friend Wayne Barlow gave me the idea of having a roller in the crutch. I had been lifting my mast and walking it back to the crutch and putting it in place-- like a dumbbell. Heck it's easier to roll it back and forth.

  • 0
  • 0
DSC00442 I used to have to raise the crutch to a higher position before I started using the Gin Pole but having a Trex block under my mast tabernacle now allows the height needed over my closed companionway hatch to leave the crutch all the way down.

DSC00442 I used to have to raise the crutch to a higher position before I started using the Gin Pole but having a Trex block under my mast tabernacle now allows the height needed over my closed companionway hatch to leave the crutch all the way down.

  • 0
  • 0
DSC00435 Note where I am standing as I am letting the mast down. I want to be situated where I can grab hold of the mast if something goes haywire. The boom vang allows me to do just that. I'm not sure if the boat winch would allow this type of freedom.

DSC00435 Note where I am standing as I am letting the mast down. I want to be situated where I can grab hold of the mast if something goes haywire. The boom vang allows me to do just that. I'm not sure if the boat winch would allow this type of freedom.

  • 0
  • 0
DSC08342 This mast only weighs about 65 lbs and it's easy to raise without the Gin Pole. I used to raise the mast by hand and use a 3/8"X 60' nylon line with a sheave connected to the bow stem chainplate to hold the mast up. I spliced an eye on one end of the line and connected it to my Jib shackle. The Jib halyard was raised and cleated to the mast with the line running through the sheave on the bow. Once the mast was up, I'd take the line around the mast above the goose neck fitting, and tie it off to my starboard bow cleat after pulling all the slack out of the line. Then the fore stay could be connected. If you have a quick release lever on your backstay or a Johnson Handy-Lock, you can throw enough slack into your forestay so that you can remove it. You never need to touch the other turnbuckles on the O'Day 222. A press button quick pin can be used on the fore stay. Do not use a fast pin!

DSC08342 This mast only weighs about 65 lbs and it's easy to raise without the Gin Pole. I used to raise the mast by hand and use a 3/8"X 60' nylon line with a sheave connected to the bow stem chainplate to hold the mast up. I spliced an eye on one end of the line and connected it to my Jib shackle. The Jib halyard was raised and cleated to the mast with the line running through the sheave on the bow. Once the mast was up, I'd take the line around the mast above the goose neck fitting, and tie it off to my starboard bow cleat after pulling all the slack out of the line. Then the fore stay could be connected. If you have a quick release lever on your backstay or a Johnson Handy-Lock, you can throw enough slack into your forestay so that you can remove it. You never need to touch the other turnbuckles on the O'Day 222. A press button quick pin can be used on the fore stay. Do not use a fast pin!

  • 0
  • 0
IMG 2298

IMG 2298

  • 0
  • 0
Racing at Shore Acres Yacht Club, Barnegat Bay nj

Racing at Shore Acres Yacht Club, Barnegat Bay nj

  • 0
  • 0
Top Bottom