Once bitten, twice shy.
I think the model number is correct although I am not sure. I have heard it referred to as a "Classic".As to why MacGregor's have a bad reputation, the following is an excerpt of a letter which I wrote to them, and may give an indication as to the reason. MacGregor did not even respond, and this is usually a good indicator of what to expect.I have posted copies of the photographs which were included with the letter on my website, and anyone who may wish to view them should go to:- www3.telus.net/Callisto (Case sensitive) Click on the link to the Server, then Downloads -> Special -> Files, and you will find a copy of the photographs there. They are labelled MacGregor 1, 2 and 3.I should add also that, in the correspondence, I also mention that there was very little caulking in the hull-to-deck joint, and, to be more specific, I think the actual length of this joint is in the region of 60', and, as close as I could measure it, my boat only had about 42' of caulking, and not all of this was as wide as one would expect either.**************"I purchased one of the above boats in 1994, and am writing to convey to you how thoroughly disgusted I am with this product.We have no local dealer in this area, and consequently I was required to drive approximately 1,400 miles to take possession. Apart from what I considerd a very serious delivery problem, which has nothing to do with your Company, when I arrived home I found there was about 10 gallons of water in the storage area below the bunks. The dealer had told me that he had washed the boat and I thought therefore that he had merely been a little careless with the hose. I dried it and about 2 weeks later tried the boat on our local channel. When I arrived at the overnight anchorage, I discovered that I had holed the water bottle and so, once again, I had water under the bunks. I removed this and thought it strange that there was more water than the bottle held, but concluded that I must have missed some previously.Within the first 3 weeks of using the boat, I discovered that the mainsail control line was either faulty, or simply of such inferior quality material, that it should not even be on the market. As you can see from the enclosed photograph, which I have labelled #1 on the back, the inner core popped out at intervals for a considerable length.I then purchased a set of cockpit cushions, and when they arrived, the seat portion of the cushions did not fit. I contacted the dealer and he had these replaced. It was some time later that I realized the the cushions which had been sent, were the long port side bunk cushions, which had been covered in vinyl, rather than the other fabric used in the interior. This could only have been done by MacGregor.The next problem I encountered was that I could not adjust the mainsail to allow a smooth air flow. The sail had a permanent crease in it which could not be corrected. I once again contacted the dealer who arranged for it to be sent to a sailmaker for repair. The sailmaker advised me that the problem was caused bythe rope on the leading edge of the sail being too short, and consequently the sail could not be fully extended.My next purchase was a boom vang, confident that there was almost no possibility whatsoever of again receiving lines of the poor quality I had received previously, but, as you can see, once again, from the enclosed photograph, labelled #2, there was no improvement. I have also only used this twice, so I expect it will get much worse. For the first 3 years of ownership, 1994 - 1996, the water problem continued, and was very serious at times. I could always rationalize where it came from, but was never certain. This was extremely annoying, because a sailboat with water in is a sailboat with water in, but a MacGregor sailboat with water in is a sailboat with water in that has no storage. Finally I had it completely dry and it was sitting in my driveway, when it rained. The rain lasted about 6 hours and when it was over, the boat had about 5 gallons of water in it. I then knew that there was something drastically wrong, and started trying to trace the problem. Almost immediately I found that when water was poured onto the forward running light, it did not all run off. A considerable amount of it ran through and into the boat. I removed the light and found that, apart from the socket of the screw holding it on being stripped, there was almost no caulking beneath it. I corrected the caulking, and then added an additional amount along the entire seam of the hull to deck rubber seal, Although this did help a little, it did not solve the problem. I tried everything to stop the leaks but finally gave up in disgust. In mid 1996 I placed the boat in storage and swore I would never use it again.However, this year I decided to try to sell it, but it is well known in this area as being a "lemon", so I knew I had little or no chance of success. Except for the front 3 feet, it had been under cover the entire 3 years, and when I opened it, it had about 15 gallons of water in it. I knew then that my only alternative was to re caulk the hull to deck joint. When I opened this, I found the source of much of the problem, but still have not solved it completely. I knew for sure then also that MacGregor, apart from using sub standard materials, could not possibly have any quality control at all. Not all the bolts securing the joint were silver either, as one would expect from stainless steel. Some were a very distinct brown colour. Judging by the condition of the heads on a number of them also, I would guess that the damage also was not caused by only one use either, unless the wrench used in the assembly did not fit correctly. I believe that it is more likely that the bolts were not new. Many were not tightened and, in fact, in one group of 10, nine were loose. One did not even have a nut on. I also found an insignificant crack in the deck section of the cockpit and although I believe this has not contributed to my problem, I cannot but wonder whether or not there is another that I have not found.The one part of the process which was easy, was actually removing the existing caulking, not because of the product used, but because there was so little of it. I am enclosing a photograph, #3, of some of the strips removed intact, which shows this very clearly. I should add that some sections did not have any at all."