the part of my pedadistall that holds the shifter and throttle lever broke, I need that center peice or a good used merriman marine pedistal that will fit my boat eric @ 419 656 1732 or ericw55@aol.com
hunter 34 pedastal
- Thread starter sunfire1
- Start date
- Status
search around on the site, Eric.. here is one thread:
http://forums.hunter.sailboatowners.com/showthread.php?p=645753&highlight=merriman pedistal
You may be able to change the plastic part only for a lot less than retrofitting Edson.. Good Luck..
http://forums.hunter.sailboatowners.com/showthread.php?p=645753&highlight=merriman pedistal
You may be able to change the plastic part only for a lot less than retrofitting Edson.. Good Luck..
Hi Eric,
Had the same problem and someone on HOW directed me to Robert Osaki at Joe's Racing . Not sure it is the same company mentioned by Steve. but what I received was perfectly machined in aluminum and came with plastic bushings for the levers.
Very little adjustment needed on my part to re-assemble the unit. Cost was $160 + shipping.
Here is the link: robert@joesracing.com
Good luck to you
Had the same problem and someone on HOW directed me to Robert Osaki at Joe's Racing . Not sure it is the same company mentioned by Steve. but what I received was perfectly machined in aluminum and came with plastic bushings for the levers.
Very little adjustment needed on my part to re-assemble the unit. Cost was $160 + shipping.
Here is the link: robert@joesracing.com
Good luck to you
eh- mon ami Claude- se moi!
=======
I put my lever box in last Spring- got it from Constance Machine -I also had it powder coated locally for $50 or it would eventually pock from the salt exposure. pictures sent directly to sunfire's email as its diffcult to edit size here.
Sunfire - here's the contact info
Robert Osaki
Joes Racing Products
1410 80th St. SW Unit F
Everett, WA 98203
office: 425-267-9199
email: robert@joesracing.com
Price about $160.00 (when I bought mine a year ago or so.)
Same day shipping, UPS ground from Everett, Washington. Shipping time 3 days to Southern California, 5 days to Florida and East Coast states.
New shaft bushings included.
Payment by credit card, VISA or MasterCard.
Contact : Robert at JOES Racing Products
1410 80th St. SW, Unit F
Everett, WA 98203
425-267-9199
email - robert@joesracing.com
=======
I put my lever box in last Spring- got it from Constance Machine -I also had it powder coated locally for $50 or it would eventually pock from the salt exposure. pictures sent directly to sunfire's email as its diffcult to edit size here.
Sunfire - here's the contact info
Robert Osaki
Joes Racing Products
1410 80th St. SW Unit F
Everett, WA 98203
office: 425-267-9199
email: robert@joesracing.com
Price about $160.00 (when I bought mine a year ago or so.)
Same day shipping, UPS ground from Everett, Washington. Shipping time 3 days to Southern California, 5 days to Florida and East Coast states.
New shaft bushings included.
Payment by credit card, VISA or MasterCard.
Contact : Robert at JOES Racing Products
1410 80th St. SW, Unit F
Everett, WA 98203
425-267-9199
email - robert@joesracing.com
extra comment- constance and Joe's seem to be related companies.
Remember to use a hex wrench to remove your old throttle side machine set screw from the old lever box- use it in the new lever box to load/stiffen and keep the throttle in position( throttle walk). don't over tighten when you insert in new housing.
Remember to use a hex wrench to remove your old throttle side machine set screw from the old lever box- use it in the new lever box to load/stiffen and keep the throttle in position( throttle walk). don't over tighten when you insert in new housing.
I put a cast/machined aluminum one in on my '85 H-34 many years back; MUCH better than the old plastic one; don't remember who I bought it from, but it could have been Constance Machining.. I am glad that Robert over there is keeping the pattern/computer machining file !
- Status