On the electrical Control Panel to the left of the stairs: Is there a site to view the amp amounts for each designated function. I need to buy new circuit breakers for the whole panel (fresh water damage)and don't know what to buy. The wires look fine. Thanks, TOM
- Status
Wiring Diagram for H-27 (1978)
Tom, I have the orig. electrical system diagram. Although the diagram does not specify the amps of the breakers It des specify the wire size. I think you could back track from the wire size to breaker size. From top to bottom the diargram says Steaming Light #16 (White/Green) Anchor Ligth #16 (White/Red) Running Lights #16 (white) Bilge #14 (Brown) Cabin Lights #14 (Blue) All of the grounds from the breakers to the busbar are #14 (Black). From the busbar to the grount is #10 (Black) I've been thinking of upgrading my panel (I already have a second panel in the rear or the port bunk which I'll remove. I'm thinking of replacing them both with two six fuse panels side by side in a fram that I'll affix over the Nav table/station. I'll also make it up to hold my VHF. It's a winter project I tried to scan the page but it the resolution is not too fine. I can fax it to you if you give a fax number.
Tom, I have the orig. electrical system diagram. Although the diagram does not specify the amps of the breakers It des specify the wire size. I think you could back track from the wire size to breaker size. From top to bottom the diargram says Steaming Light #16 (White/Green) Anchor Ligth #16 (White/Red) Running Lights #16 (white) Bilge #14 (Brown) Cabin Lights #14 (Blue) All of the grounds from the breakers to the busbar are #14 (Black). From the busbar to the grount is #10 (Black) I've been thinking of upgrading my panel (I already have a second panel in the rear or the port bunk which I'll remove. I'm thinking of replacing them both with two six fuse panels side by side in a fram that I'll affix over the Nav table/station. I'll also make it up to hold my VHF. It's a winter project I tried to scan the page but it the resolution is not too fine. I can fax it to you if you give a fax number.
Not marked?
My c/b's(old, 1979) are marked with the amperage. But the numbers are on the body of the breaker, behind the panel. Have you got the panel out and the breakers are unlabeled? I also have wiring diagrams with only the wire size. That is not too helpful except to know that #16 and #14 are very small wires and cannot handle much current, about 25 max for #16 and 35 for #14. Which makes me think that most of my c/b's are 20 amps. Might be the only thing that I do not have written down.
My c/b's(old, 1979) are marked with the amperage. But the numbers are on the body of the breaker, behind the panel. Have you got the panel out and the breakers are unlabeled? I also have wiring diagrams with only the wire size. That is not too helpful except to know that #16 and #14 are very small wires and cannot handle much current, about 25 max for #16 and 35 for #14. Which makes me think that most of my c/b's are 20 amps. Might be the only thing that I do not have written down.
Fax on the way TO Smokey
Fax was sent at 10:05 PM EST. Let me know if the resolution it poor and I'll fax it again on Monday from my office at high resolution. HN
Fax was sent at 10:05 PM EST. Let me know if the resolution it poor and I'll fax it again on Monday from my office at high resolution. HN
Bac fax number?
Smkey, Tired to fax but it was a voice line. I assume that the voice I heard was yours.. Are you sure that 847 331 9754 is the correct fax number? HN
Smkey, Tired to fax but it was a voice line. I assume that the voice I heard was yours.. Are you sure that 847 331 9754 is the correct fax number? HN
- Status