DSC00738 In the picture you see my traveler, and manual bilge pump. Also pictured is the mount for my galley table which has a similar mount down below on the galley cabinet. By the way. I replaced that Nic Fico Traveler with a Harken rope and pulley traveler last summer of 2012. What a difference that made on my boat! The pump handle is detachable and the plate is inserted back in the hole. I've never had to use this pump. Thank the good Lord for small favors.
Mother of all mods 003 I had bought some stainless steel hooks years ago and never used them because of the fabric headliner material in my cabin. The only quick solution for using them was to screw them to small square pieces of 1/4" plywood and cementing Velcro to the backs. It works. You need to buy the Velcro in an automotive store. Regular Walmart Velcro really isn't strong enough to hold boat poles.
Mother of all mods 004 If you look to the right in this pic you can see my whisker pole laying against the side of the inside cockpit. My "pig stick" and 12' telescopic boat pole are on the other side against the inside hull.
Mother of all mods 001 I call this The Mother of all mods." It turned out to be one of the most clever and easy mods I've ever to this boat. Why didn't I think of this one before? We're looking aft in that Starboard quarter birth cubby hole. That rear plywood bulkhead used to extend up into that inside combing and I remember removing it years ago when I refinished all my woodwork but I couldn't remember if there was any useful space in there. So I figured that if I could remove that bulkhead I could find out real quick. I've always needed a place to hang my boat hook and just recently my friend Del Grindle gave me a nice Forespar Whisker pole which is about 6.5' when it's closed. At any rate, I removed the bulkhead and cut it. I made a Teak cap rail for it and like a dumbbell I decided to cover it with rug. I could have done the same thing with pine! Oh well. Some days you just can't win for losing. :)
DSC00738 In the picture you see my traveler, and manual bilge pump. Also pictured is the mount for my galley table which has a similar mount down below on the galley cabinet. By the way. I replaced that Nic Fico Traveler with a Harken rope and pulley traveler last summer of 2012. What a difference that made on my boat! The pump handle is detachable and the plate is inserted back in the hole. I've never had to use this pump. Thank the good Lord for small favors.
This gadget is clamped to my mast and it's main function is to keep the mast from going over the side as I raise/lower. I call it a mast yoke and there are temporary stays (baby stays) connected to it and pivot bridles on both sides of my boat located on the side decks near the chainplates. There are two simple rules to follow when raising/lowering the mast from the stern of the boat: 1. Always make sure that the boat is level from side to side. 2. The wind needs to be coming directly from aft. If the boat is leaning to one side, the temporary stays may not support the mast. The same holds true if a large gust of wind hits the mast from the beam of the boat while raising/lowering. In either case the mast can go over the side. If you don't have a furler, the mast yoke along with temporary stays and pivot bridles can be omitted as long as you follow those two simple rules. All that is needed is the Gin pole and the mast crutch in the stern.
This is that special hitch which I call the "Lineman's Rolling Hitch." It's very simple to tie and it absolutely won't slip on anything you tie it to. I sent it to "Grog" (Alan Grogono www.animatedknots.com) last month for his web site. Whether he'll add it to his collection of knots and hitches, I don't know.
This pic shows the vinyl furler luff loosely secured against the Gin Pole. I'm using a special hitch around the vinyl luff just above the Gin Pole which is securely tied off to the Gin Pole with this same 1/4" line.
Joe11688

DSC00738 In the picture you see my traveler, and manual bilge pump. Also pictured is the mount for my galley table which has a similar mount down below on the galley cabinet. By the way. I replaced that Nic Fico Traveler with a Harken rope and pulley traveler last summer of 2012. What a difference that made on my boat! The pump handle is detachable and the plate is inserted back in the hole. I've never had to use this pump. Thank the good Lord for small favors.

There are no comments to display.

Media information

Album
Trinkka's mods
Added by
Joe11688
Date added
View count
547
Comment count
0
Rating
0.00 star(s) 0 ratings

Image metadata

Filename
17412-1358947700-a37a88bef42de83b1b24ce31ac03bf31.jpg
File size
39.1 KB
Dimensions
800px x 600px

Share this media

Top Bottom