All Activity

What's new Recent Activity New media New media comments All Activity
  • Johann
    Johann replied to the thread Victron MultiPlus not charging after generator capactor blew.
    Have you tried turning both Multis off then back on with the physical rocker switch on the unit? Also reboot the Cerbo perhaps.
  • jssailem
    jssailem reacted to eherlihy's post in the thread Cabin top hand rail with Helpful Helpful.
    I'll tell you that IF I still used the teak handrails, I would try to use UV Curing Varnish with them. I just discovered this stuff. It...
  • jssailem
    jssailem replied to the thread Spinnaker.
    Pretty good. You may find that the messenger line exits the front of the mast on a sheave. Since your mast is rigged as a fractional...
  • fred1diver
    fred1diver replied to the thread Furler Q’s.
    The issue is that the black end cap on top is preventing the forestay from attaching itself to the mast head, that is why I NEED to add...
  • eherlihy
    eherlihy replied to the thread Cabin top hand rail.
    I'll tell you that IF I still used the teak handrails, I would try to use UV Curing Varnish with them. I just discovered this stuff. It...
    • 20260522_104743.jpg
    • 20260522_104804.jpg
  • Davidasailor26
    Davidasailor26 replied to the thread Oceanis 370 freshwater tank selector valves.
    On the newer 37 the valves are on a manifold right next to the pump, under the port settee. Be sure only one is open at a time. We also...
  • jssailem
    jssailem replied to the thread Furler Q’s.
    Ok. what if you were able to ass the length to the base? part B32 is the “Toggle Fork Fork”. If is was 2” longer that would lengthen...
    • 1782218358832.png
  • fred1diver
    fred1diver replied to the thread Start button.
    Ok, thank you very much, I was looking at the same one on Amazon last night. I need to refresh on my electronics and electrical...
  • fred1diver
    fred1diver replied to the thread Furler Q’s.
    This is the only picture I have, it was taken before I undertook the whole furler task this spring, Basically a thick pin goes through...
    • IMG_8436.jpeg
  • geoffschultz
    geoffschultz posted the thread Victron MultiPlus not charging after generator capactor blew in Ask All Sailors.
    I'm on my way from South Africa to the Newport, RI area and just arrived in Bermuda. I have a NextGen UCM 9.5 generator, and the other...
  • fred1diver
    fred1diver reacted to Ralph Johnstone's post in the thread Start button with Like Like.
    All depends on the draw of your starter relay. Now is the time to place a series ammeter at the current push button starter and see...
  • Ralph Johnstone
    Ralph Johnstone replied to the thread Start button.
    All depends on the draw of your starter relay. Now is the time to place a series ammeter at the current push button starter and see...
  • jssailem
    jssailem reacted to colemj's post in the thread Galvanic Corrosion/zinc depletion question. with Like Like.
    50Hz vs 60Hz makes no difference. As stated, AC current has little impact on stray current corrosion. If the culprit does happen to...
  • jssailem
    jssailem reacted to Ralph Johnstone's post in the thread Start button with Like Like.
    Definitely the better way to go and avoid an additional relay (the booster relay) if you can get anywhere near the wiring. I'm retired...
  • jssailem
    jssailem reacted to kloudie1's post in the thread Start button with Like Like.
    Small clarification.. After looking at the Yanmar wiring, and doing a little research on wire size etc, I decided to feed the key switch...
Show older items
Top Bottom