Menu
Menu
Log in
Register
Menu
Home
Forums
New posts
Unanswered threads
Register
Top Posts Email
What's new
New posts
New Posts (legacy)
Latest activity
New media
Media
New media
New comments
Boat Info
Downloads
Weekly Quiz
Topic FAQ
10000boatnames.com
Classifieds
Sell Your Boat
Used Gear for Sale
Parts
General Marine Parts
Hunter
Beneteau
Catalina
MacGregor
Oday
Help
Terms of Use
Monday Mail Subscribe
Monday Mail Unsubscribe
All Activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
What's new
Recent Activity
New media
New media comments
All Activity
Davidasailor26
replied to the thread
Electric toilet
.
You’ll have no problem with that amount of load and duration. 15 amps is pretty minimal compared to the couple hundred amps or more a...
Jun 1, 2026
shemandr
reacted to
Richard19068's post
in the thread
Aft cleat for Jib Sheets?
with
Like
.
Schaefer | SKU: SCH60-78 Schaefer Cleat, Jam, 4"(102mm), Silver Schaefer | SKU: SCH70-17 Schaefer Fast Entry Cam Cleat Assembly...
Jun 1, 2026
Richard19068
replied to the thread
Aft cleat for Jib Sheets?
.
Schaefer | SKU: SCH60-78 Schaefer Cleat, Jam, 4"(102mm), Silver Schaefer | SKU: SCH70-17 Schaefer Fast Entry Cam Cleat Assembly...
Jun 1, 2026
Don S/V ILLusion
replied to the thread
Electric toilet
.
And what size battery bank do you have? The load would be calculated in amp-hours, not minutes.
Jun 1, 2026
Ralph Johnstone
replied to the thread
Packing Gland
.
I would suggest following @heritage 's advice.
Jun 1, 2026
Hayden Watson
reacted to
jssailem's post
in the thread
Terminal connectors
with
Like
.
I use a spray of Corrosion Block to slow down the corrosion.
Jun 1, 2026
heritage
replied to the thread
Packing Gland
.
It could be teflon packing that is squeezed so tightly that the ends can't be seen. Have you tried digging into it with a sharp dental pick?
Jun 1, 2026
Hayden Watson
replied to the thread
Aft cleat for Jib Sheets?
.
Both my Clipper 26 and Catalina 30 had jam cleats for the headsail sheets, and they never let loose when I did not want them to...
Jun 1, 2026
shemandr
replied to the thread
Aft cleat for Jib Sheets?
.
Cam, jam, clam - I think there's confusion about each. I would agree with Stu's post if it were about jam cleats which I don't trust...
Jun 1, 2026
Maine Sail
replied to the thread
Terminal connectors
.
This may help: Crimp Heat Shrink Terminals Like a Pro
Jun 1, 2026
Dalliance
reacted to
BigEasy's post
in the thread
Rant on dual helms
with
Like
.
Perhaps on boats over 45’ in length, dual helms are an improvement in design & practicality. No way, no how, can I see a boat in the...
Jun 1, 2026
Dalliance
reacted to
Project_Mayhem's post
in the thread
Rant on dual helms
with
Like
.
I feel the same way about shift/throttle levers at shin height
Jun 1, 2026
Stu Jackson
replied to the thread
Aft cleat for Jib Sheets?
.
Clam cleats are notorious for intermittent holding. As such, they are a poor choice for this application. IIRC, my 1981 C22 #10496...
Jun 1, 2026
D
dlochner
replied to the thread
Hunter 41DS prop shaft to gearbox key way falling out
.
As tight as you can get them!
Jun 1, 2026
BigEasy
reacted to
jssailem's post
in the thread
DIY Bowsprit Anchor Hanger made of ROPE? Danforth Anchor
with
Like
.
There is a bowline knot that has two loops. This might be a solution. The loops are adjustable after you have tied the knot. This might...
Jun 1, 2026
Top
Bottom
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…