Media added by Dennis Kitchen

Navigation

Browse albums

Media comments

  • A
    1975 o'day 22
    will be changing to led lights both mast and cabin along with nav lights. adding solar, adding bbq, rebedding all deck hardware and below water...
  • Monsterfish
    Looking forward to V-berth.
    Wow.....dream home!
  • D
    MacGregor 26s
    Das sind Teakleisten, die aufgeklebt, dann mit Schwarzer Masse ausgegossen und geschliffen wurden. Sieht immer noch aus wie neu.....
  • P
    Marilee-Interior.jpg
    This interior is gorgeous! What type of boat is this in?
  • JohnScott
    DSCN8846
    CHILD LABOR

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
IMG 0327 New six gallon marine water tank. 2013

IMG 0327 New six gallon marine water tank. 2013

  • 0
  • 0
IMG 0328Sink.Pump New galley pump and water tank fill. 2013

IMG 0328Sink.Pump New galley pump and water tank fill. 2013

  • 0
  • 0
IMG 0359Trailer New bunks and carpet 2013

IMG 0359Trailer New bunks and carpet 2013

  • 0
  • 0
IMG 0364 Centerboard bushing bore repair 2013

IMG 0364 Centerboard bushing bore repair 2013

  • 0
  • 0
IMG 0379 Old and new centerboard pins and bushing. 2013

IMG 0379 Old and new centerboard pins and bushing. 2013

  • 0
  • 0
000 0217 Work in progress. Pin bores were built up and faired with thickened epoxy.

000 0217 Work in progress. Pin bores were built up and faired with thickened epoxy.

  • 0
  • 0
000 0218 Centerboard all repaired with thickened epoxy and fiberglass. Entire board coated in epoxy then bottom painted. (not shown)

000 0218 Centerboard all repaired with thickened epoxy and fiberglass. Entire board coated in epoxy then bottom painted. (not shown)

  • 0
  • 0
000 0223 Centerboard hanger; board and rope roller pins. Pins were too short to stay engaged while assembling into hull so I added the epoxy buttons on ends each side and custom trimm ed for a light slip fit in well. Origonally had duct tape holding in the pins.

000 0223 Centerboard hanger; board and rope roller pins. Pins were too short to stay engaged while assembling into hull so I added the epoxy buttons on ends each side and custom trimm ed for a light slip fit in well. Origonally had duct tape holding in the pins.

  • 0
  • 0
000 0222 centerboard hanger bottom painted (upside down)

000 0222 centerboard hanger bottom painted (upside down)

  • 0
  • 0
000 0212 centerboard hanger

000 0212 centerboard hanger

  • 0
  • 0
000 0211Well foreward closeup.

000 0211Well foreward closeup.

  • 0
  • 0
000 0206 Well looking aft.

000 0206 Well looking aft.

  • 0
  • 0
000 0205 Well looking up and forward. Notice rough jagged edges of bolt hole. I smoothed this with a knife and sealed edges with epoxy.

000 0205 Well looking up and forward. Notice rough jagged edges of bolt hole. I smoothed this with a knife and sealed edges with epoxy.

  • 0
  • 0
000 0202 opposite side

000 0202 opposite side

  • 0
  • 0
000 0203 What freezing water does to damaged centerboard

000 0203 What freezing water does to damaged centerboard

  • 0
  • 0
000 0069 Custom biminis stowed

000 0069 Custom biminis stowed

  • 0
  • 0
000 0094 Custom biminis deployed

000 0094 Custom biminis deployed

  • 0
  • 0
000 0106 Interior... like the Admirals' custom pillows?

000 0106 Interior... like the Admirals' custom pillows?

  • 0
  • 0
000 0214 Old bottom coming off

000 0214 Old bottom coming off

  • 0
  • 0
000 0230 New bottom, boot and shear stipes

000 0230 New bottom, boot and shear stipes

  • 0
  • 0
Top Bottom