Media added by aduffE37

Navigation

Browse albums

Media comments

  • A
    1975 o'day 22
    will be changing to led lights both mast and cabin along with nav lights. adding solar, adding bbq, rebedding all deck hardware and below water...
  • Monsterfish
    Looking forward to V-berth.
    Wow.....dream home!
  • D
    MacGregor 26s
    Das sind Teakleisten, die aufgeklebt, dann mit Schwarzer Masse ausgegossen und geschliffen wurden. Sieht immer noch aus wie neu.....
  • P
    Marilee-Interior.jpg
    This interior is gorgeous! What type of boat is this in?
  • JohnScott
    DSCN8846
    CHILD LABOR

Media statistics

Albums
3,799
Uploaded media
22,708
Embedded media
19
Comments
425
Disk usage
2.2 GB
mr oliver on his throne

mr oliver on his throne

  • 0
  • 0
we all know the feeling

we all know the feeling

  • 0
  • 0
It was late

It was late

  • 0
  • 0
My good buddy Brandon who came all the way down to florida to help in a boat yard

My good buddy Brandon who came all the way down to florida to help in a boat yard

  • 0
  • 0
I hate being in this position. damn Endeavours!

I hate being in this position. damn Endeavours!

  • 0
  • 0
Beautifully finished

Beautifully finished

  • 0
  • 0
filler, this stuff is aluminium powder. the side of the can says dont use near open flame. i tried to light it with a lighter but nothing happened. this stuff turned out to be the easiest to manipulate in a putty type form.

filler, this stuff is aluminium powder. the side of the can says dont use near open flame. i tried to light it with a lighter but nothing happened. this stuff turned out to be the easiest to manipulate in a putty type form.

  • 0
  • 0
before blister repair, nasty stuff man

before blister repair, nasty stuff man

  • 0
  • 0
Taking too much off. the Mexicans of the yard soon came to our rescue and told us to take less off and showed us how to use the angle grinders. Those guys were awsome!

Taking too much off. the Mexicans of the yard soon came to our rescue and told us to take less off and showed us how to use the angle grinders. Those guys were awsome!

  • 0
  • 0
Naked

Naked

  • 0
  • 0
My new rapid/easy oil change fitting. i had some high temp hyrolic hoses with fitting built to siphon the oil from the down slopped engine....awsome pat pat on my back thank you!

My new rapid/easy oil change fitting. i had some high temp hyrolic hoses with fitting built to siphon the oil from the down slopped engine....awsome pat pat on my back thank you!

  • 0
  • 0
The nasty nasty!!!

The nasty nasty!!!

  • 0
  • 0
Preping the surface. just to think how much time it took to get to this tiny little aluminum pot metal cover!

Preping the surface. just to think how much time it took to get to this tiny little aluminum pot metal cover!

  • 0
  • 0
ahhh the culprit. This is where all the oil comes from (usually) with the perking 4-108, at least thats what they told me i should fix to stem the oil in the bilge.

ahhh the culprit. This is where all the oil comes from (usually) with the perking 4-108, at least thats what they told me i should fix to stem the oil in the bilge.

  • 0
  • 0
My beautiful girlfriend making my boat look even cooler

My beautiful girlfriend making my boat look even cooler

  • 0
  • 0
up on blocks

up on blocks

  • 0
  • 0
Pulling the perkins: rear main seal, all new hoses and better type hose clamps, plumb in a rapid oil change fitting (flip a switch and the hot oil gets sucked out of the bottom of the engine), new oil pan gasket, pull the heat exchnager and clean, new motor isolators, re wire harnesses, rebuild starter, referb velvet drive, install new shaft and pyi dipless packing gland......wow what a 2 month project. this is my buddy that helps gotta love thos guys

Pulling the perkins: rear main seal, all new hoses and better type hose clamps, plumb in a rapid oil change fitting (flip a switch and the hot oil gets sucked out of the bottom of the engine), new oil pan gasket, pull the heat exchnager and clean, new motor isolators, re wire harnesses, rebuild starter, referb velvet drive, install new shaft and pyi dipless packing gland......wow what a 2 month project. this is my buddy that helps gotta love thos guys

  • 0
  • 0
Kinded hauled out and finishing the bottom paint. Trinidad SR 3 coats

Kinded hauled out and finishing the bottom paint. Trinidad SR 3 coats

  • 0
  • 0
red is coming off......subsequently brought the hul down to patent gelcoat and fixed blisters where they were....(not many) sealed in epoxy then five coats of interprotect and the addition of a wash down pum with new through hulls with counter sunk silicone bronse fasteners.

red is coming off......subsequently brought the hul down to patent gelcoat and fixed blisters where they were....(not many) sealed in epoxy then five coats of interprotect and the addition of a wash down pum with new through hulls with counter sunk silicone bronse fasteners.

  • 0
  • 0
Top Bottom