Search results


    HUNTER 49/50 Fischer Panda 12 Mini Generator noise

    When the generator is running I am getting a constant "ticking" noise most noticeable in the aft starboard cabin (especially when the floor hatch is removed), or when accessing the aft engine access from the hanging locker. The noise appears to be coming out of the water separator. I do not hear...

    Hunter 50 Raymarine Stng question

    I am in the process of replacing my defective SPX30 autopilot with a new ACU400 autopilot. The old fluxgate compass was connected to the SPX30 via a 5 wire connection, while the EV-1 connects via Stng. While installing the new EV-1 heading sensor, I found a Stng "T" connector for the depth...

    Raymarine SPX-30 autopilot repair

    Anyone know where I could get my autopilot computer repaired? Raymarine wants a fortune.

    Box thruster repair in water?

    The "hub" or gearbox installed in my Hunter 41DS needs replacement. It is a Lewmar 140TT part # 581001. I am wondering if it would be possible to dam up the starboard side of the tunnel, and then tip the boat over with the halyard enough to get the port end of the tunnel out of the water. The...

    Bulb type for steaming light, 2006 H41

    Hi All, Anyone know what type of bulb is used in the steaming light on a 2006 Hunter 41? Thanks

    Electronics overheating?

    3 weekends ago my both wind displays showing wind speed and direction (ST60 & ST70) stopped working when wind speed hit around 25 knots, and started working again about an hour and a half later when the wind speed decreased to around 15 knots. Soon after I removed the wood cover that encloses...

    PVC Thread sealant

    Anyone know what type of thread sealant Hunter used on the PVC threaded connections on the holding tank valve?

    Screeching noise from Bow Thruster

    I have had a number of issues with Lewmar 140TT bow thruster on my 41DS. Thruster worked perfectly before having boat hauled for bottom job. After hauling, thruster worked, but had electrical issue remedied by replacement "T" type fuse. Then had to replace shear pin which fell out of shaft...

    "T" Type Fuse

    Got to my 2007 Hunter 41DS 2 days ago. Tried to turn on the TV (which is fed 120 volts AC thru a dedicated 12 volt DC inverter), but TV would not turn on. Then I noticed that the 12 volt meter on DC panel was acting strangely. When I turned on a DC load such as the engine compartment blower, the...

    Replacing Jabsco pumps

    I am replacing my broken Jabsco maserator pump with a Seaflo unit. Of course the Jabsco broke by the bolts snapping because they are NOT made of stainless. This has happened on 2 Jabsco units, which is just amazing. When they snap, of course they leak which at best is disgusting and at worse can...

    Lazy Jacks Hunter 50

    Can anyone tell me how to correctly rig the lazy jacks? As I am not the original owner, I don't know if the sail cover is from Hunter? The system has a fixed cable with eye that extends from the spreaders, attached about 18" from the mast. The movable lines are then attached thru this eye, and...

    NMEA 0183 Connection in Hunter 50

    Does anyone know what is connected to the NMEA 0183 terminals on the Raymarine X30 autopilot in my 2011 Hunter 50? When I disconnected the connector all systems (GPS, depth, etc) worked fine. My paddle wheel for speed is kaput so I can't tell if anything changed. Also my VHF was still getting a...

    Battery for Raymarine SR 130

    Does anyone know the size number for the replacement battery?

    Removing freezer WAECO CB-40 from Hunter 49/50

    Need to replace one of the 2 freezers in my Hunter 50. Ordered new one from WM. Anyone have any advise on removal?

    Replacing Raymarine RS 130 GPS Antenna

    I am having issues with the GPS heading indication on my Raymarine E120. As indicated by the RED vector line, it sometime is correct and is sometimes out by up to 120 degrees. Sometimes it responds correctly after I turn the boat in a circle, sometimes not. Green vector line works correctly...

    Halyard line not holding in rope clutch

    After raising my main sail and setting the rope clutch, the line does not hold but slips back about a foot. I believe the problem is the double braid I am using is too loosely weaved and gets pinched by the clutch. It has been suggested that I need a tighter weaved braid, one that is NOT...

    Hunter 49/50 Boost Gauge & Water in Fuel Modification

    I have already modified the standard M200 engine monitoring system to show engine information on the Raymarine E120 MFD's, which also includes a boost pressure gauge. I have purchased the correct Yanmar boost sensor, which I plan to install in the rubber hose coming off the intake manifold on my...

    Hunter 49/50 Waeco CB-40 Freezer

    One of the 2 built in freezers has stopped cooling after winter lay up. Have tried turning thermostat on & off. Compressor/fan is running under unit when I turn on thermostat, so it appears electrical connection OK. Anyone have any info on removal and/or repair? New unit around $960.00.

    Optimal voltage setting for Balmar 614 and Magnum charger

    My boat has 3 Deka Gel 8D batteries with a total ampere rating @ 20 hours of 675. Deka states "charge to at least 13.8v, but no more than 14.6v @77 degrees" . Both my Magnum charger and Balmar 614 (Balmar AT-165 Alternator) have battery temperature sensors attached. I would appreciate...

    Removal of cabin top winch

    Any ideas appreciated! Need to remove cabin top winch which appears to be holding on tight due to 5200 used as a sealant at Hunter factory. Am planning to use piano wire and/or a sharpened putty knife to cut thru sealant.