Search results

  1. joker460

    Funny Friday!!!

  2. joker460

    Transom to hull crack

    The transom is molded as part of the deck and is attached to the hull with Goop (as Ron20324 indicated). That looks like either the boat backed into something hard or someone drove into it. The problem with the photo is, it looks like the crack is not equal across the split. May be some...
  3. joker460

    Beneteau 361 stiff steering

    That's good news. UHMW is also used in the Beverage Industry for wear strips under the conveyor beds and guide rails. The only reason my rudder needs the thrust washer is because our bearing would allow the rudder to bottom out against the hull without it.. Your photo of the rudder tube shows a...
  4. joker460

    Beneteau 361 stiff steering

    I've seen that style of rudder somewhere.....https://forums.sailboatowners.com/threads/411-rudder-removal.169591/ rickbogh had the same stiff steering with the same style of rudder post #14 and #18
  5. joker460

    Beneteau 361 stiff steering

    The picture showing the lower bushing looks interesting. Was this fixed previous or is that from the factory.? It may be the way the picture is shown, but it looks like the adhesive has bonded the shaft and bushing so the bushing was rotating within the rudder tube. (Just an observation) Also...
  6. joker460

    ProFurler Basic B35 Foil

    Don't see if you are on the American or Canadian side of Lake St. Clair but I get my profurl info from: WPG Canada 169, rang 5 ouest Stoke, Qc J0B 3G0 Tel: (819) 878-3018 info@wichard.ca / www.wpgcanada.com They will recommend which dealer is closest to you and give you the part numbers to...
  7. joker460

    Orca Attacks?

    Nah, He's the son of Edmund
  8. joker460

    110 V plugs not working.

    You must have the Wiring Diagram as shown below.
  9. joker460

    Crash. Pray for these people

    That will buff out just fine:laugh: At least no one was hurt badly.
  10. joker460

    In-Mast Furling Question - Beneteau Oceanis 400

    It looks like your boom is way over to the port side. If you move it towards the centre or to starboard it will not rub. Remember you have a block on the boom just forward of the vang which guides the inhaul line. Just my 2 cents Picture is of a bene 351
  11. joker460

    Wiring Diagrams for a 2009 Beneteau 31

    You probably have this manual BENETEAU OCEANIS 31 Owner's Manual (Page 137 of 138) | ManualsLib It has no wiring diagram. The manual does shows that there are only 1 Red disconnect for the Engine Battery and 1 Red disconnect for the Service batteries, and 1 Black disconnect (Ground). Note that...
  12. joker460

    The kind of year it has been

    Nice, but who is hiding under the table:)
  13. joker460

    Toerail damage B323 finding a replacement

    Or $80 a foot :yikes:
  14. joker460

    Toerail damage B323 finding a replacement

    You need to contact Beneteau USA as there is something on their site as shown below. Looks like it's $260 per meter and it's in stock.
  15. joker460

    Access to behind the cooler box?

    In a couple of Beneteau's and mine the microwave was held in place by 6, double sided sticky rubber pads.
  16. joker460

    Why Oceanis boats cost so much more than Sun Ods?

    Just my 2 cents. If you compare the Sun Odyssy 349 base price $125K (Single wheel, Single rudder, Smaller engine) to the Oceanis 35.1 base price $150k (Dual wheel, Dual Rudder, Larger engine) Both have a hull length of 32'-9". Both are owned by the same company I believe. They are not that far...
  17. joker460

    Funny Friday!!!

  18. joker460

    When and Where is the Sale, Sale, Sale

    There's the DockShoppe in Toronto The Dock Shoppe Don't know if the West Marine Shop in Toronto is still open? There's the Rigging Shoppe in Scarbourgh Rigging Shoppe Ltd. Fogh Marine in Toronto Fogh Boat Supplies | Store | Power and Sail - Boating Electronics, Boat Electrical, Boat Plumbing...
  19. joker460

    Anybody know if there's a master "reset" for a Raymarine ST4000+ autohelm?

    Try Here: Ray Marine ST-4000 Problem
  20. joker460

    Another Raymarine wind speed issue.

    One other thing to ask. Did you disconnect the yellow wire from the display and then measure it. If the voltage doesn't vary, then the mast head unit is knackered. But you said that you replaced the circuit board, Did you test it before you put it up on the mast head? Hard to diagnose from a...