Search results

  1. Syntonos

    More Yamaha 25 prop shaft Questions

    Nope, haven't had the opportunity. It will be the #1 project next time I haul out for bottom paint. Best wishes to all through the holidays .
  2. Syntonos

    yamaha 25 refit

    Glad to be of help. nice you have the place to "get after it" without the layday charges of a boat yard! It will be nice when your done knowing you've " been there - done that" To bad we didn't get together when you were in LA. checking out the boat. we are definitely on the same page, I to...
  3. Syntonos

    yamaha 25 refit

    Welcome to the wild world of the Y25. I've attached a couple of photos of the raw water strainer on my boat. it is mounted on the forward bulkhead of the engine box. The gray valve is a 3 way which allows me to fresh water flush the engine and back-flush the strainer. The hose connection is...
  4. Syntonos

    Sunforce Marine 600watt Wind Generator

    Excellent, thanks for the lead, that will help greatly. I always like to know where I'm going ...before I get there! Thanks to all those in the Sailboatowners community ... best resource on the planet.
  5. Syntonos

    Sunforce Marine 600watt Wind Generator

    the parts list doesn't break down the alternator, only the assembly. I was hoping to come up with alt. model (AC-Delco, Hitachi etc.) prior to having to measure the existing bearing to reduce downtime. Thanks.
  6. Syntonos

    Sunforce Marine 600watt Wind Generator

    Hello All, I'll be working on an older Sunforce Marine 600 wind generator in the near future, with an internal noise. I would like to identify what alternator they are using prior to disassembly. Internet searches and customer support has been futile other than schematic and a parts...
  7. Syntonos

    New owner of 'Shamanita' Y25 (SF Bay)

    I Do have the patterns of my boat. I strongly suggest copying your own as they are not symmetrical. I too regretted cutting the floor....obviously it had to be done. I did the floor removal and pattern work / pre-fabrication in the water prior to haul out. Cutting the G20 was a chore done at my...
  8. Syntonos

    New owner of 'Shamanita' Y25 (SF Bay)

    Welcome aboard the Yamaha Forum. this is the only active forum I have found for the Y25. We have covered a lot of ground over the years. Haul Out: inform the lift operator of the prop shaft exiting the keel, they will have to sling between prop and skeg rudder. Blisters seem to be...
  9. Syntonos

    More Yamaha 25 prop shaft Questions

    Does anyone know the O.D. of the cutlass bearing? while the shaft is 22mm ( 7/8) the O.D. of off the shelf 7/8 cutlass bearing is a much larger diameter. I have no problem turning down the OD. I need the strut I.D. before tearing out the old cutlass. Any help from the Y25 crows feel free to...
  10. Syntonos

    Y26 rig tuning advice

    Your correct on the mast head vs. fractional. I just wanted to make the point looser seems to work better than stiff on my boats performance. You may want want to look up a Thistle one design tuning guide , as well as others, that use a fractional rig. Thats where I cut my jib back in the day...
  11. Syntonos

    Y26 rig tuning advice

    Hello Hoosgow, I have a Y25. I've attached the Y25 manual that has a good tuning section that works for me. I figure the basics are similar to the Y26. I have Dyform rigging so shroud tension # are irrelevant. I rely more on mast performance in various conditions. I use rig tension to...
  12. Syntonos

    Yamaha 25' ...head?

    US models came with porta potty, Others with Head. my boat has the thru hulls so the previous owner installed the flush head. Use of a bladder on the port fwd compartment works well. Don't use it often but handy when its needed. A well vented and maintained system has worked well with no...
  13. Syntonos

    Rig Tension Specs

    I imagine your 30 instructions aren't far off from my Y25 method. I set my rig per the manual then took the loos #'s as a base line. You can compare tuning methods for the Y25 by checking out the pdf manual a few posts back . syntonos
  14. Syntonos

    Y-25 PARTS

    There ya go gobluemich290, two solutions to the problem, welcome to the forum!
  15. Syntonos

    Y-25 PARTS

    Unfortunately he passed away a number of years ago, and yes he was a master metal magician. Any good metal fabricator / welder will be able to duplicate the process. It requires two machined bocks be welded in place to accept studs for bolt mounts. Which y25 did you buy? Thought I new all the...
  16. Syntonos

    Y-25 PARTS

    Wow, looks like the world wide solution! My friend ( a welder/fabricator) and I came up with the same idea using 1 inch stainless square tube cut diagonally. Only difference is a whole lot of polishing!!!! Nice job Furdui! P.S My friend always believed " if your going to do something - do it...
  17. Syntonos

    Y25 II Manual in PDF

    Here it is, knew I had it somewhere.
  18. Syntonos

    Y25 Weather helm !

    My pleasure, As I had mentioned, you now have a world class boat, I too was thrilled to find all our fellow Yamaha fans through out our world. I'll be hauling out in a few weeks. I always receive compliments on how stiff the "old " Yamaha is compared to boats of lesser years. Keep in mind the...
  19. Syntonos

    Y25 Weather helm !

    Here you go! Straight from Yamaha.... if you'd like the complete copy contact me in private messages. Cheers Syntonos
  20. Syntonos

    Y25 Weather helm !

    Welcome aboard ! Your boat looks great. Check out the earlier posts as we have covered a lot of issues over the last few years. FYI, this is your best source for your Yamaha we have dialog from around the globe. I believe one lists a link for a PDF manual in English. I do have a printed copy...